$10 to $25

The Decoder Buddy Mini was developed to fit into smaller steam and diesel applications.  there has also been interest in HOn3 and S-Gauge applications. This mother board does not include the 21 Pin Decoder. This mother board requires soldering. These printed circuit board is  NOT INTENDED FOR USE IN A DC SYSTEM. The mother board includes:  One 21 Pin Decoder receptacle Two pairs of track input pads One pair of motor input pads One set of stay alive pads (U+ , GND and if necessary a third control wire ) One pair of speaker pads Resistors for use with LED lighting. (Also available with 0 ohm, 750 ohm and custom specified resistors for function outputs. This accommodates some previously installed and "12 volt LEDs".)  It is IMPORTANT to realize that resistors must be used when LEDs are connected to the four lighting outputs of the Mini!!!  The resistors may be soldered in line when purchased or the included resistors may be soldered inline upon installation.  Remember there are different incandescent lamp voltage requirements and current draw that have to be taken into consideration also. (Until the next batch is produced the Mini will be labeled Tiny and the picture on the package will indicate the correct headlight outputs for direction of locomotive.)

Read more less

Static Grass 28 grams Grass length: 12mmm

Read more less

Turn lights on and off with the flick of a switch. Control the power to a Light Hub, Sequencing Light Hub, Expansion Hub or to multiple Hubs. Easily mount switch to main control panel with mounting screws or double-sided tape, if desired. Switch face includes labeling space for quick identification. ROHS Compliant

Read more less

Red LED Flashing Nano Lights 30mA Includes 24" cables 2 lights per package Ready to plug into Light Hub (sold separately) INSTRUCTIONS: Align locking tabs on Light Plug with front of Light Hub (JP5700, JP5701) and insert into LIGHT Port until locking tabs click into place. Glue or tape Light in place, as required. Pink plastic band (1/2") on cable identifies Red Flashing light.

Read more less

This speaker is perfect for enhancing the low bass sounds that are found in most diesel decoders. It is well worth the extra effort! Dimensions: 23 x 23 x 10.2mm(D)Frequency Response: 275Hz – 20kHzPower: 2 Watts (Nominal) 4 Watts (Peak)Impedance: 8 Ohms

Read more less

This speaker is great for boosting the low frequencies in most diesel and “big” steam sounds. Dimensions: 27 x 14.3mm(D)Frequency Response: 350Hz – 20kHzPeak Power: 2 WattsImpedance: 8 Ohms

Read more less

Add texture and highlights to scenery Blends naturally with other foliage For any scale 57.7 in3 (945 cm3)

Read more less

This product is versatile in terms of direction of the placement of the board and mounting in various configurations.  It can easily replace a QSI board, a Dual Mode decoder board or be mounted directly on the electric motor or frame with Kapton tape.  (It is recommended that a piece of Kapton tape be placed on the bottom of the mother board to assure electrical isolation from the electric motor or frame.) This mother board does not include a 21 Pin Decoder. This mother board and connector board require soldering. These printed circuit boards are NOT INTENDED FOR USE IN A DC SYSTEM. The on board resistors are sized for some 12 volt LEDs.  Package Includes: 1x Mother Board 1x Connector Board Dimensions: 0.67" x 2.20" x 0.35" (17 mm x 56 mm x 0.9 mm)The mother board includes;  One 21 Pin Decoder receptacle Two pairs of track input pads One pair of motor input pads One pair of stay alive pads (U+ and GND) Two pairs of speaker pads wired in parallel Resistors for use with LED lighting.  (Also available with 0 ohm, 750 ohm and custom specified resistors for function outputs.  this accommodates incandescent lamps or bulbs.) The connector board contains pads for eight pairs of lighting function connections. U+ or the blue wire has eight connected pads for the common power source. The negative (-) discrete function pads are all labeled to indicate their connection to the functions available in the decoder. The lighting connector was designed so that the shell of the diesel locomotive can be easily separated from the frame without un-soldering wires. This does require that the headlight and rear lights be mounted in the shell of the locomotive and that the diesel has a removable dynamic brake shell. Incandescent lamps or bulbs are not well suited for the Decoder Buddys or associated decoders.  It can be done but it will require more electronics to achieve a result.  Our recommendation is to go with LEDs.

Read more less

The Decoder Buddy Mini was developed to fit into smaller steam and diesel applications.  there has also been interest in HOn3 and S-Gauge applications. This mother board does not include the 21 Pin Decoder. This mother board requires soldering. These printed circuit board is  NOT INTENDED FOR USE IN A DC SYSTEM. Included with board are four axial resistors to be mounted remotely inline and are sized for LEDs. (2.2K) The mother board includes:  One 21 Pin Decoder receptacle Two pairs of track input pads One pair of motor input pads One set of stay alive pads (U+ , GND and if necessary a third control wire ) One pair of speaker pads Resistors for use with LED lighting. (separate axial 2.2K)  (Also available with 0 ohm, 750 ohm and custom specified resistors for function outputs. This accommodates some previously installed and "12 volt LEDs".)  It is IMPORTANT to realize that resistors must be used when LEDs are connected to the four lighting outputs of the Mini!!!  The resistors may be soldered in line when purchased or the included resistors may be soldered inline upon installation.  Remember there are different incandescent lamp voltage requirements and current draw that have to be taken into consideration also. (Until the next batch is produced the Mini will be labeled Tiny and the picture on the package will indicate the correct headlight outputs for direction of locomotive.)

Read more less

The PTB-100 Programming Track Booster is a handy tool for anyone who uses DCC! This device facilitates programming as well as gives some comforting feedback during the programming process. You will instantly know if your decoder has received the programming instruction (or not!) by way of indicator lights on the circuit board. So why might you want (or need) a PTB-100? Certain command stations allow you to read a CV during Service Mode programming, which is useful to verify its current setting. Sometimes trouble reading or verifying CVs may be due to the design of the command station and the decoder itself. All decoders communicate back to the command station using what’s called an acknowledgement pulse, which is defined in NMRA RP-9.2.3 as “an increased load on the programming track of at least 60mA for at least 5ms.” Like most decoders, SoundTraxx Digital Sound Decoders generate the acknowledgment pulse by momentarily applying power to the motor. If the decoder is otherwise working properly (i.e., responds properly on the mainline to speed and direction commands), but the command station is having trouble reading CV data from the decoder, it may be due to incompatibilities between the electrical requirements of the sound decoder (which are different from conventional decoders due to the added audio circuitry) and the electrical characteristics of the programming track. In this case, you will need to use a programming track booster, such as the PTB-100. The PTB-100 amplifies the programming track signals to levels that work best with SoundTraxx Sound Decoders. It is easy to install and inexpensive. An advantage to using the PTB-100 is that it also provides short circuit detection and some helpful diagnostics. The PTB-100 is neither needed nor recommended for use with the Zimo MX1 or the Lenz LVZ100.

Read more less

The TSU-2200 is a versatile Digital Sound Decoder that is suitable for a wide variety of models from HO to S scale. You will feel like you are in the cab with the amazing new features that Tsunami2 has to offer including: Reactive Dynamic Digital Exhaust, Functioning locomotive and train brakes, injectors, power reverse, and firebox flicker. We also offer a large selection of selectable sound effects including: exhaust chuffs (10), prime movers (up to 12), bells (12), Whistles (90), airhorns (40+), couplers, dynamos and more! This 2-amp, universal-style format, and includes a connector to easily add a CurrentKeeper (P.N. 810140) to maintain performance over dirty track and switches. Product Specifications: Sound Profile: ALCO Diesel Dimensions: 35 x 18 x 6mm Max. Motor Stall Current: 2A Max. Function Current: 100mA (each output) Function Outputs: 6 Audio Amplifier: 2 Watt, 8-Ohm Load DCC Track Voltage: 7.5V – 22V Sound Channels: 16

Read more less

The TSU-2200 is a versatile Digital Sound Decoder that is suitable for a wide variety of models from HO to S scale. You will feel like you are in the cab with the amazing new features that Tsunami2 has to offer including: Reactive Dynamic Digital Exhaust, Functioning locomotive and train brakes, injectors, power reverse, and firebox flicker. We also offer a large selection of selectable sound effects including: exhaust chuffs (10), prime movers (up to 12), bells (12), Whistles (90), airhorns (40+), couplers, dynamos and more! This 2-amp, universal-style format, and includes a connector to easily add a CurrentKeeper (P.N. 810140) to maintain performance over dirty track and switches. Product Specifications: Sound Profile: EMD-2 Diesel Dimensions: 35 x 18 x 6mm Max. Motor Stall Current: 2A Max. Function Current: 100mA (each output) Function Outputs: 6 Audio Amplifier: 2 Watt, 8-Ohm Load DCC Track Voltage: 7.5V – 22V Sound Channels: 16

Read more less