The Digitrax SE74 Signal Decoder is a must-have for any model train enthusiast. With its multi-scale compatibility and precise control, you can easily customize and automate your train signals. Benefit from the professional and objective tone of this product, which relies on domain expertise and scientific language to deliver top-notch performance. Fully connectorized installation. Optional support for DCC 9-Aspect control mode, including Lunars. Easy setup with Option Switches and LocoNet programming. Configurable for four solenoid or four slow-motion turnout control. 8 Input lines for local control and sensors. 8 System routes with 8 entries each. Advanced LocoNet configuration capability with Series7 style installation support using a DT602. More Information Item # SDCK Brand Digitrax MSRP $22.00 TCA Grading C-10 Mint - Brand New Availability In-Stock/Restockable Manuals Instruction Sheet / Specification Sheet

Read more less

Dual Stationary Decoder for Bi-polar, Snap Switches or Slow Motion Machines DS52 Features: Simple hook up and set up. Control 2 individual turnout machines.2 Slow motion turnout machines, such as Tortoise™ by Circuitron or Switchmaster™.OR2 Solenoid type turnout machines such as three wire Peco or Atlas Snap Switches or two wire bi-polar type turnout machines such as Kato Unitrack, AristoCraft, or LGB turnouts with powerful capacitive discharge capability. Turnout addresses can be set individually or in groups of 2. Screw terminals make installation easy! DCC compatible. Screw terminals make installation and set up easy. Control 2 solenoid type turnout machines: 2 wire bi-polar (Kato Unitrack Switches, etc.) and/or 3 wire (Peco, Atlas Snap Switches, etc.) Addresses can be independent or sequential All Scales up to 22V track power. More Information Item # DS52 Brand Digitrax Scale Multi Scale MSRP $28.00 TCA Grading C-10 Mint - Brand New Availability In-Stock/Restockable Manuals Specification Sheet / Instruction Sheet

Read more less

This snap-together baffle kit is designed for use with our 15mm round speakers (P.N. 810089).

Read more less

Lower cost than older AM-1! The TC-1 is a module that you can install on your model train layout and control 4 turnouts (switch tracks).  The TC-1 can be controlled and setup by a Ring Engineering RailPro Controller, such as the HC-3 Handheld Controller.  Features: Control up to 4 turnouts per Module Control Snap or Motor Operated Turnouts Size: 4.60 x 3.00 x 1.18 inches Package Contents: TC-1 Turnout Control Module User Manual You will need a RailPro controller such as a HC-3 (Handheld Controller with Color Touch Screen - Not Included) to control, setup and monitor a TC-1.

Read more less

The Digitrax SE74 Signal Decoder is a must-have for any model train enthusiast. With its multi-scale compatibility and precise control, you can easily customize and automate your train signals. Benefit from the professional and objective tone of this product, which relies on domain expertise and scientific language to deliver top-notch performance. Fully connectorized installation. Optional support for DCC 9-Aspect control mode, including Lunars. Easy setup with Option Switches and LocoNet programming. Configurable for four solenoid or four slow-motion turnout control. 8 Input lines for local control and sensors. 8 System routes with 8 entries each. Advanced LocoNet configuration capability with Series7 style installation support using a DT602. More Information Item # SE74 Brand Digitrax MSRP $119.00 TCA Grading C-10 Mint - Brand New Availability In-Stock/Restockable Manuals Instruction Sheet

Read more less

Includes 3 Signal Masts that can be used as Signal Mast Bases in any scale or can be painted and detailed and used as N-scale signal masts. More Information Item # SMBK Brand Digitrax MSRP $17.00 TCA Grading C-10 Mint - Brand New Availability In-Stock/Restockable Manuals Instruction Sheet / Specification Sheet

Read more less

HO scale Mainline Signaling Kit including: 2 Single Head A Signals, 2 Single Head B Signals, 4 SMP1s, 8 spacers, 8 screws. Makes all of your signals plug ‘n play with small 10 pin connectors. Can be used as a basic HO scale signal. Mounting board and hardware included. Current setting resistors are built in to the board. Easy mainline setup with A and B mast configurations. Pads are provided to make it easy to attach any signal to the mast base. This product is intended for use with the SE8C. The Digitrax Plug ‘N Play Signal Mast consists of a signal mast with one or two signal heads depending on mast configuration. Included with the kit are mounting boards and hardware that makes it easy to mount and connect the signal mast to the SE8C signal driver cable. This product is intended for use with the SE8C and other Digitrax signaling decoders. More Information Item # SH2AB Brand Digitrax MSRP $27.00 TCA Grading C-10 Mint - Brand New Availability In-Stock/Restockable Manuals Instruction Sheet

Read more less

Under layout mounting hardware for Signal Driver Cables and their sockets. 6 metal signal straps and 6 signal spacers. These handy bits of hardware hold your signal plugs at just the right distance from the layout to make it easy to plug in your signals. More Information Item # PM74 Brand Digitrax Warranty No Worries Warranty (read more) MSRP $12.00 TCA Grading C-10 Mint - Brand New Availability In-Stock/Restockable Manuals Instruction Sheet / Specification Sheet

Read more less

The new ESU PowerPack Maxi has been developed as the powerful complement to the LokSound L V4.0 /  LokSound  5 L decoder. It can, of course, provided there is sufficient space, also be connected to all LokPilot V4.0, LokSound V4.0, LokSound V4.0 M4, LokPilot 5 or LokSound 5 decoders. It provides uninterrupted power to your locomotive when traversing dirty track and long turnout ladders. All sound, lighting and motor functions are buffered with the aid of two energy storage capacitors enabling your models – subject to the total energy consumption - to continue running for up to three seconds. The PowerPack Maxi incorporates an integral charging circuit controlled by the decoder. Therefore it may be connected even during programming. The charging current is limited in order to avoid an undue load on the booster, in case there are several models in the same booster sector. The buffer time can be reduced by means of a CV. This may be useful to assure the correct stopping position ahead of signals showing the “Stop” aspect (red signal). The space requirements of the PowerPack Maxi of about 27.5 mm x 15.7 mm x 13 mm must be taken into account when installing this unit. A three-pole wire harness connects the PowerPack Maxi to the decoder. The wires are already soldered to the PowerPack Maxi but must be soldered to the appropriate solder pads of the decoder. Please note that due to technical reasons the PowerPack cannot operate in analogue mode: Buffering is therefore not possible in analogue mode. More Information Item # 54672 Brand ESU Scale Multi WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

If necessary, you can add the Decoder Tester Extension to your Profi Decoder Tester: Plugged into the side of the Decoder Tester it enables you to comfortably test all large scale decoders. If you also have to deal with large scale LokSound XL or LokSound L decoders in your workshop, the Profi Decoder Tester Extension is just the right thing for you: You can plug on LokSound XL decoders with multi-pin connectors as well as LokSound L decoders directly and easily test them. The extension module has multi-pin connectors for direct plug-on of the decoder types mentioned above. An LED monitor with 12 LEDs displays the status of all physical function outputs. You may also plug on a second speaker or sensor inputs onto the multi-pin connector for quick and easy testing. Up to four servos may also be plugged on for direct testing. Especially for the LokSound L, connecting pins for a smoke generator have also been added. The Profi Decoder Tester Extension represents the perfect test and programming bench in conjunction with the Profi Decoder Tester, where you can test and program almost all (ESU) decoders quickly and easily. WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

Perhaps you are familiar with this scenario: there is a digital decoder sitting on your workbench and you want to test it prior to a perhaps complex installation. But how to do this? The Profi Decoder tester makes it easy for you: simply connect the tester to your command station or the LokProgrammer. It enables you to test any decoder without exposing it to any external factors caused by the locomotive that may influence its performance. Features In order to make things as easy as possible for you, the Profi Decoder Tester is equipped with some useful features. It has all commonly used interface sockets for connecting a decoder for the smaller scale models: Besides a 6-pole NEM 651 socket and the 8-pole NEM 652 socket, it also has an 21MTC interface as per NEM 660, a PluX22 socket as well as a Next18 interface: No matter which type of decoder you have: Simply plug it in – it will fit! And that’s all there is to it! Decoders without any interface can be contacted with individual terminals.  A quality coreless motor with flywheel serves in conjunction with LEDs indicating the direction for checking the motor output: Thus it is quite easy to check on the low speed performance and the even speed of the decoder. An LED monitor informs you about the functioning of the headlights and back-up lights as well as the function outputs AUX1 through AUX6. For testing LokSound decoders we have integrated a 20 mm speaker. You may choose if the integral speaker should be switched off or if it should have 100 Ohm respectively 16 Ohm – thus the Decoder Tester is perfectly suitable for any ESU decoder generation! Two SUSI plugs facilitate the direct test of optional SUSI modules as well as the connection to another circuit board. The electrical connection to either the command station or the LokProgrammer is facilitated by a removable, 2-pole terminal block (same system as used on the LokProgrammer and the ECoS) or via two solder points. Extension Now there is an extension board that enables you to also connect our large scale decoders to the Decoder Tester. With this vast range of components your Profi Decoder Tester will soon be an indispensable aid in your workshop! More Information Item # 53900 Brand ESU TCA Grading C-10 Mint - Brand New Availability In-Stock/Restockable Manuals Instructions for ESU Decoder Tester 53900 WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less