Gift Ideas Under $100.00

Perhaps you are familiar with this scenario: there is a digital decoder sitting on your workbench and you want to test it prior to a perhaps complex installation. But how to do this? The Profi Decoder tester makes it easy for you: simply connect the tester to your command station or the LokProgrammer. It enables you to test any decoder without exposing it to any external factors caused by the locomotive that may influence its performance. Features In order to make things as easy as possible for you, the Profi Decoder Tester is equipped with some useful features. It has all commonly used interface sockets for connecting a decoder for the smaller scale models: Besides a 6-pole NEM 651 socket and the 8-pole NEM 652 socket, it also has an 21MTC interface as per NEM 660, a PluX22 socket as well as a Next18 interface: No matter which type of decoder you have: Simply plug it in – it will fit! And that’s all there is to it! Decoders without any interface can be contacted with individual terminals.  A quality coreless motor with flywheel serves in conjunction with LEDs indicating the direction for checking the motor output: Thus it is quite easy to check on the low speed performance and the even speed of the decoder. An LED monitor informs you about the functioning of the headlights and back-up lights as well as the function outputs AUX1 through AUX6. For testing LokSound decoders we have integrated a 20 mm speaker. You may choose if the integral speaker should be switched off or if it should have 100 Ohm respectively 16 Ohm – thus the Decoder Tester is perfectly suitable for any ESU decoder generation! Two SUSI plugs facilitate the direct test of optional SUSI modules as well as the connection to another circuit board. The electrical connection to either the command station or the LokProgrammer is facilitated by a removable, 2-pole terminal block (same system as used on the LokProgrammer and the ECoS) or via two solder points. The dimensions of the ESU Decoder Tester are 99 x 74 x 34mm. WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

INPUT: 120VAC, 60Hz OUTPUT: 24VDC, 1000mA Type A RoHS Compliant

Read more less

HO-scale, 4-function decoder that measures 25.1 x 15.6 x 4.7mm. This decoder has a 21-pin connector arranged according to the NMRA Standard that easily plugs into the factory-installed PCB of many models. This decoder will operate in DCC only. Dimensions: 25.1 x 15.6 x 4.7mm  Max. Motor Stall Current: 1A Max. Function Current: 100mA (each output) Function Outputs: 4 DCC Track Voltage: 21 Volts Maximum

Read more less

Plug this USB module into your PC (Personal Computer) to add Direct Radio to your computer so you can control and setup RailPro products like the RailPro locomotive modules!You can use a CI-1 and a PC to get started with RailPro for a lower cost! You can buy a real RailPro handheld controller at a later time.PC Requirements: Windows 10, Windows 8, Windows 7, and Vista. Product Specifications: Interface: USB-A Dimensions: 1.87 x 0.78 x 0.34 in   Download the CI-1 Software Here!  

Read more less

Use the Expansion Hub to connect up to four Light Hubs, expanding your Just Plug Lighting System quickly and easily. Add an optional Auxiliary Switch for convenient operation. Do NOT plug LED lights into Expansion Hub Powering Your Light System- You will need one Just Plug Power Supply (JP5770 US, JP5771 Euro, JP5772 UK, or JP5773 Aus/NZ) to power up to 50 lights on your light system, or if you want to power your system from a train power pack, purchase Connecting Cables (JP5760). ROHS Compliant

Read more less

Use the Port Sharing Device with a Light Hub or Sequencing Light Hub to add up to four Stick-On or Nano LED Lights per Light Port. Provide power quickly and easily to all of your Just Plug products. Just Plug's modular design allows for easy expansion and gives you the ability to control individual light brightness.

Read more less

The LM-3S is a module that you can install into a model train locomotive so the locomotive can be controlled and setup by a Ring Engineering RailPro Controller, such as the HC-2 Handheld Controller with a Color Touch Screen! After the LM-3S is installed in a locomotive, you will be able to control the locomotive speed, direction, up to 6 light outputs and sounds! The LM-3S has “Direct Radio” (RF transceiver) built inside. The built in RF module allows commands and data to be sent and received to and from the module. You can load a picture of your choice into the LM-3S module. Then you will be able to touch the screen of the HC-2 to take control of your locomotive! You can even download new sounds and light effects using the built in Direct Radio!The LM-3S is electrically compatible with the DCC plug found in many locomotives to promote easy installation. Product Specifications: Sound Profile: Universal (all) Dimensions: 1.50 x 0.68 x 0.25 in DCC Track Voltage: 7.5V – 18V Light Outputs 6   The LM-3 is equipped with Direct Radio! This allows Ring Engineering Controlling Devices such as the HC-2, Handheld Controller with Color Touch screen, to control and configure your locomotive by sending and receiving data directly to the LM-3 through the air by use of RF transmission! The Direct Radio is very fast giving your locomotive quick response to your controls. Further, a controlling device can detect your LM-3 with just a few touches on the screen. Because of Direct Radio, you can load a picture of your locomotive to the LM-3! You can also load Light Effects and much more!Radio Load Sharing is a truly an innovative invention from Ring Engineering. It allows your locomotives that are linked together (sometimes called Consisted or MU'ed) to actually share pulling power. Only RailPro equipped locomotives use Direct Radio to talk to each other to be sure each locomotive pulls its share of the load! Even more amazingly, Ring Engineering's patent pending process only takes seconds to setup!Six light outputs. Can be configured for multiple light effects on a single output including On/Off, Dim, Ditch, Mars, Strobe, and more! Additional light effects can be loaded using DirectRadio!Built in protection with fault reporting by Direct Radio!Tiny size 1.50 x 0.68 x 0.25 Inches for easy fit.

Read more less

Easily connect a CurrentKeeper or extra capacitor to any SoundTraxx decoder equipped with a 2-pin “Quick Plug” to improve performance over dirty track and switches.

Read more less

#206 Insulated Muti-Purpose Coupler Height Gauge - HO ScaleIncludes the #148 Whisker® Coupler & #158 Scale Whisker® Coupler. - Kit. EASY TO ASSEMBLE & USE A must have tool for gauging mounting height, correct coupler height, trip pin, and permanent uncoupler heights for achieving trouble free coupler performance. Also has a built in HO track gauge. "Takes the guess work out" Four tools in one.1. Provides instant visual reference of proper coupler height.2. Accurately measures proper trip pin height above rail.3. Built-in track gauge. (N.M.R.A. Standard)4. Movable dowel tests Kadee® Magne-Matic® Uncoupler height and registers the needed adjustments.5) Provides instant visual reference of proper body mounting height.Track not included Package Includes: (1) each #148 Whisker® Coupler (1) each #158 Whisker® Coupler (1) each #206 Lid (1) each #206 Dowel (1) each #206 Height Gauge Base (10) each .015 Red Fiber Washers (2) each #622 Knuckle Springs (2) each #625 Knuckle Springs (1) each 2 x 1/4" Screw

Read more less

The PTB-100 Programming Track Booster is a handy tool for anyone who uses DCC! This device facilitates programming as well as gives some comforting feedback during the programming process. You will instantly know if your decoder has received the programming instruction (or not!) by way of indicator lights on the circuit board. So why might you want (or need) a PTB-100? Certain command stations allow you to read a CV during Service Mode programming, which is useful to verify its current setting. Sometimes trouble reading or verifying CVs may be due to the design of the command station and the decoder itself. All decoders communicate back to the command station using what’s called an acknowledgement pulse, which is defined in NMRA RP-9.2.3 as “an increased load on the programming track of at least 60mA for at least 5ms.” Like most decoders, SoundTraxx Digital Sound Decoders generate the acknowledgment pulse by momentarily applying power to the motor. If the decoder is otherwise working properly (i.e., responds properly on the mainline to speed and direction commands), but the command station is having trouble reading CV data from the decoder, it may be due to incompatibilities between the electrical requirements of the sound decoder (which are different from conventional decoders due to the added audio circuitry) and the electrical characteristics of the programming track. In this case, you will need to use a programming track booster, such as the PTB-100. The PTB-100 amplifies the programming track signals to levels that work best with SoundTraxx Sound Decoders. It is easy to install and inexpensive. An advantage to using the PTB-100 is that it also provides short circuit detection and some helpful diagnostics. The PTB-100 is neither needed nor recommended for use with the Zimo MX1 or the Lenz LVZ100.

Read more less

Brand: JT's Mega Steam Scent: Coal-Fired Steamer Size: 2 Oz Glass Bottle with Eye Dropper Made in the USA

Read more less

Spray-Tac is a spray adhesive for adhering Flowers and Plant Hues. It sprays in a fine mist and dries to a clear, matte finish.

Read more less