Plug this USB module into your PC (Personal Computer) to add Direct Radio to your computer so you can control and setup RailPro products like the RailPro locomotive modules!You can use a CI-1 and a PC to get started with RailPro for a lower cost! You can buy a real RailPro handheld controller at a later time.PC Requirements: Windows 10, Windows 8, Windows 7, and Vista. Product Specifications: Interface: USB-A Dimensions: 1.87 x 0.78 x 0.34 in Download the CI-1 Software Here!
$31.99
Quantity: Two per packageThe WH-9 wiring harness can be used with all RailPro Locomotive modules. The WH-9 conforms to NMRA 9 pin plug standard so it can be used for any DCC locomotive where applicable. The WH-9 wiring harness can be used to add the required DCC 9 pin plug (JST) to a non-DCC locomotive. Or you can use it after removing all circuit boards from a DCC equipped or DCC ready locos (too allow a cleaner installation or make more room for a RailPro module). Please see LM instructions for actual wiring. JST connectors can come in two different ways that the pins are connected to the wires (crimp style and insulation displacement) both connect in the same manner and are interchangeable. However, we have found the crimp style pins to be far more dependable than the insulation displacement connectors that some DCC suppliers sell. WH-9 has a JST 9 pin with crimp style pins.
$6.39$5.75
The LM-3S is a module that you can install into a model train locomotive so the locomotive can be controlled and setup by a Ring Engineering RailPro Controller, such as the HC-2 Handheld Controller with a Color Touch Screen! After the LM-3S is installed in a locomotive, you will be able to control the locomotive speed, direction, up to 6 light outputs and sounds! The LM-3S has “Direct Radio” (RF transceiver) built inside. The built in RF module allows commands and data to be sent and received to and from the module. You can load a picture of your choice into the LM-3S module. Then you will be able to touch the screen of the HC-2 to take control of your locomotive! You can even download new sounds and light effects using the built in Direct Radio!The LM-3S is electrically compatible with the DCC plug found in many locomotives to promote easy installation. Product Specifications: Sound Profile: Universal (all) Dimensions: 1.50 x 0.68 x 0.25 in DCC Track Voltage: 7.5V – 18V Light Outputs 6 The LM-3 is equipped with Direct Radio! This allows Ring Engineering Controlling Devices such as the HC-2, Handheld Controller with Color Touch screen, to control and configure your locomotive by sending and receiving data directly to the LM-3 through the air by use of RF transmission! The Direct Radio is very fast giving your locomotive quick response to your controls. Further, a controlling device can detect your LM-3 with just a few touches on the screen. Because of Direct Radio, you can load a picture of your locomotive to the LM-3! You can also load Light Effects and much more!Radio Load Sharing is a truly an innovative invention from Ring Engineering. It allows your locomotives that are linked together (sometimes called Consisted or MU'ed) to actually share pulling power. Only RailPro equipped locomotives use Direct Radio to talk to each other to be sure each locomotive pulls its share of the load! Even more amazingly, Ring Engineering's patent pending process only takes seconds to setup!Six light outputs. Can be configured for multiple light effects on a single output including On/Off, Dim, Ditch, Mars, Strobe, and more! Additional light effects can be loaded using DirectRadio!Built in protection with fault reporting by Direct Radio!Tiny size 1.50 x 0.68 x 0.25 Inches for easy fit.
$79.99
RailPro products by Ring Engineering are professional grade, powerful, and very easy to use model railroad control products that can be enjoyed by beginners and experts alike. RailPro products by Ring Engineering are professional grade, powerful, and very easy to use model railroad control products that can be enjoyed by beginners and experts alike. The HC-3 is a wireless controller with a color touch screen that can be used to operate your model railroad layout. The HC-3 can control the speed, direction, lights, and sounds of locomotives and other accessories by simply touching the screen! All you need in addition to this starter kit is at least one locomotive module. The included power supply has enough power to run 15 typical modern HO Scale locomotives. You can add additional power supplies, handheld controllers, locomotive modules, and accessory modules, to expand this starter set to control practically any size layout! Package Contents: HC-3 Handheld Controller Battery Charger (100-240VAC 50/60Hz) USB Cable PWR-56 Module PA-2 Power Adapter (110-220VAC 50/60Hz) 110 VAC Power Cable User Manual with Quick Start Guide Please see HC-3 and PWR-56 for more details on each product.
$309.99
Quantity: One per packageThe WH-6 wiring harness is used with LM-3, LM-3S, LM-2, and LM-2S modules. It is used to wire in light outputs 5 and 6 and more. Please see LM instructions for actual wiring. WH-6 has a JST 6 pin with crimp style pins. We have found the crimp style pins to be far more dependable than the insulation displacement connectors.
$6.39$5.75
This product is specifically designed to be used with DC and/or RailPro products. It cannot be used with DCC products. The AR-1 is used to power special configurations of track such as below. Track configuration like below would cause a short circuit if connected without the use of an AR-1. Note that if you follow Rail ’A’ around you will notice that it connects to Rail ‘B’! That is just like putting a piece of metal across Rail ’A’ and Rail ‘B’ which would cause a short circuit and would cause a power supply to shut down. The solution to power special track configurations like below is to add insulation gaps and power the sections with an AR-1. The AR-1 can also be used to isolate small sections of track, limiting the impact of short circuits if derailments occur to just one area of your layout. Features: All Solid State Design Simple Connection with Only 4 Wires No Adjustments Necessary Provides Short Circuit Isolation for a Section of Track Status Indicator Light Fast and Secure Spring Clamp Connecters Fully Enclosed Circuit Board Electronics Size: 4.60 x 3.00 x 1.18 inches Our all solid state design has many advantages over relay based designs. With the relay based designs we tested you could see the locomotive jerk when it crossed the gap at slow speeds. With our AR-1 we saw no visible change in speed at all! Further, compared to relay based designs, solid state units are far less likely to fail, switch many times faster and all without that annoying relay clicking sound.
$31.99$28.79
