$10 to $25

The Decoder Buddy Mini was developed to fit into smaller steam and diesel applications.  there has also been interest in HOn3 and S-Gauge applications. This mother board does not include the 21 Pin Decoder. This mother board requires soldering. These printed circuit board is  NOT INTENDED FOR USE IN A DC SYSTEM. The mother board includes:  One 21 Pin Decoder receptacle Two pairs of track input pads One pair of motor input pads One set of stay alive pads (U+ , GND and if necessary a third control wire ) One pair of speaker pads Resistors for use with LED lighting. (Also available with 0 ohm, 750 ohm and custom specified resistors for function outputs. This accommodates some previously installed and "12 volt LEDs".)  It is IMPORTANT to realize that resistors must be used when LEDs are connected to the four lighting outputs of the Mini!!!  The resistors may be soldered in line when purchased or the included resistors may be soldered inline upon installation.  Remember there are different incandescent lamp voltage requirements and current draw that have to be taken into consideration also. (Until the next batch is produced the Mini will be labeled Tiny and the picture on the package will indicate the correct headlight outputs for direction of locomotive.)

Read more less

The Decoder Buddy Mini was developed to fit into smaller steam and diesel applications.  there has also been interest in HOn3 and S-Gauge applications. This mother board does not include the 21 Pin Decoder. This mother board requires soldering. These printed circuit board is  NOT INTENDED FOR USE IN A DC SYSTEM. The mother board includes:  One 21 Pin Decoder receptacle Two pairs of track input pads One pair of motor input pads One set of stay alive pads (U+ , GND and if necessary a third control wire ) One pair of speaker pads Resistors for use with LED lighting. (Also available with 0 ohm, 750 ohm and custom specified resistors for function outputs. This accommodates some previously installed and "12 volt LEDs".)  It is IMPORTANT to realize that resistors must be used when LEDs are connected to the four lighting outputs of the Mini!!!  The resistors may be soldered in line when purchased or the included resistors may be soldered inline upon installation.  Remember there are different incandescent lamp voltage requirements and current draw that have to be taken into consideration also. (Until the next batch is produced the Mini will be labeled Tiny and the picture on the package will indicate the correct headlight outputs for direction of locomotive.)

Read more less

The Decoder Buddy Mini was developed to fit into smaller steam and diesel applications.  there has also been interest in HOn3 and S-Gauge applications. This mother board does not include the 21 Pin Decoder. This mother board requires soldering. These printed circuit board is  NOT INTENDED FOR USE IN A DC SYSTEM. Included with board are four axial resistors to be mounted remotely inline and are sized for LEDs. (2.2K) The mother board includes:  One 21 Pin Decoder receptacle Two pairs of track input pads One pair of motor input pads One set of stay alive pads (U+ , GND and if necessary a third control wire ) One pair of speaker pads Resistors for use with LED lighting. (separate axial 2.2K)  (Also available with 0 ohm, 750 ohm and custom specified resistors for function outputs. This accommodates some previously installed and "12 volt LEDs".)  It is IMPORTANT to realize that resistors must be used when LEDs are connected to the four lighting outputs of the Mini!!!  The resistors may be soldered in line when purchased or the included resistors may be soldered inline upon installation.  Remember there are different incandescent lamp voltage requirements and current draw that have to be taken into consideration also. (Until the next batch is produced the Mini will be labeled Tiny and the picture on the package will indicate the correct headlight outputs for direction of locomotive.)

Read more less

This Light Test Board module replaces the existing connector board and plugs directly into the NixTrainz Decoder Buddy Adapter Board to make programming, testing, and diagnostics work quick and easy.  The test module has LEDs on-board so you can program, test and troubleshoot your installation with ease.   Compatible with: Decoder Buddy Original (1k Ohm, 8 Outputs) Decoder Buddy Version 5 (12 Outputs) Decoder Buddy Mini (1k Ohm Resistors Onboard) Decoder Buddy Mini (Separate Resistors Included)  

Read more less