DCC Accessories
SoundTraxx SoundTraxx 810140 | CurrentKeeper™
The SoundTraxx CurrentKeeper™ is designed to add additional power capacity to any decoder installation. It can be used to overcome dirty track, limited electrical pickup or dead frogs to ensure reliable operation of any locomotive in your fleet. It measures 40 x 6 x 11mm.
£20.79
SoundTraxx SoundTraxx 810160 | CurrentKeeperII | Multi Scale
Introducing the More Compact CurrentKeeperII! Not all models are made the same, and some are a TIGHT fit for a decoder installation. The CurrentKeeper is now available in two sizes to fit more models and make your installs easier! Keep more of your trains running even over dirty track and switches! The NEW SoundTraxx CurrentKeeperII™ is designed to add additional power capacity to any decoder installation. It can be used to overcome dirty track, limited electrical pickup or dead frogs to ensure reliable operation of any locomotive in your fleet. It measures 20.1 x 13.2 x 11mm. ● Maintains power to the decoder for up to 6 seconds during electrical interruptions● Compatible with NMRA DCC Standards & Recommended Practices
£20.79
SoundTraxx SoundTraxx 810135 | 9-pin JST to NMRA 8-pin Wiring Harness
The SoundTraxx 9-pin JST to NMRA 8-pin wiring harness easily converts TSU-2200 or ECO-200 Digital Sound Decoders to plug and play decoders for use with models equipped with an NMRA 8-pin socket.
£8.80
SoundTraxx SoundTraxx 810110 | 28mm Speaker Baffle Kit
This snap-together baffle kit is designed for use with SoundTraxx’s 28mm round speakers (P.N. STX810054 or STX810153).
£5.02
SoundTraxx SoundTraxx 810158 | CurrentKeeper 2-Pin Wiring Harness
Easily connect a CurrentKeeper or extra capacitor to any SoundTraxx decoder equipped with a 2-pin “Quick Plug” to improve performance over dirty track and switches.
£5.65
Ring Engineering Ring Engineering AR-1 RailPro Auto Reverse Module
This product is specifically designed to be used with DC and/or RailPro products. It cannot be used with DCC products. The AR-1 is used to power special configurations of track such as below. Track configuration like below would cause a short circuit if connected without the use of an AR-1. Note that if you follow Rail ’A’ around you will notice that it connects to Rail ‘B’! That is just like putting a piece of metal across Rail ’A’ and Rail ‘B’ which would cause a short circuit and would cause a power supply to shut down. The solution to power special track configurations like below is to add insulation gaps and power the sections with an AR-1. The AR-1 can also be used to isolate small sections of track, limiting the impact of short circuits if derailments occur to just one area of your layout. Features: All Solid State Design Simple Connection with Only 4 Wires No Adjustments Necessary Provides Short Circuit Isolation for a Section of Track Status Indicator Light Fast and Secure Spring Clamp Connecters Fully Enclosed Circuit Board Electronics Size: 4.60 x 3.00 x 1.18 inches Our all solid state design has many advantages over relay based designs. With the relay based designs we tested you could see the locomotive jerk when it crossed the gap at slow speeds. With our AR-1 we saw no visible change in speed at all! Further, compared to relay based designs, solid state units are far less likely to fail, switch many times faster and all without that annoying relay clicking sound.
£25.23
NixTrainz NixTrainz | Decoder Buddy Light Test Board
This Light Test Board module replaces the existing connector board and plugs directly into the NixTrainz Decoder Buddy Adapter Board to make programming, testing, and diagnostics work quick and easy. The test module has LEDs on-board so you can program, test and troubleshoot your installation with ease. Compatible with: Decoder Buddy Original (1k Ohm, 8 Outputs) Decoder Buddy Version 5 (12 Outputs) Decoder Buddy Mini (1k Ohm Resistors Onboard) Decoder Buddy Mini (Separate Resistors Included)
£10.25
SoundTraxx SoundTraxx 810138 | 35 x 16mm Speaker Gasket Kit
Package of four gaskets for mounting SoundTraxx 35 x 16mm oval speakers (P.N. STX810113).
£5.02
SoundTraxx SoundTraxx 810119 | 28mm Speaker Gasket Kit
Package of four gaskets for mounting SoundTraxx 28mm round speakers (P.N. STX810054).
£4.89
SoundTraxx SoundTraxx 810163 | JST-N18 Adapter | N Scale
This adapter allows you to use our smallest decoder (The TSU-N18) in practically any n-scale model! Bring the TSU-N18's 6 functions plus a narrower profile to your models. The JST-Next18 Adapter features a Next18 socket to simply plug-in your TSU-N18 decoder and solder pads for additional functionality. Dimensions: 16 x 9.5 x 5mm. P.N. 810163. Dimensions: 16 x 9.5 x 5mm Function Outputs: 6 Max Function Current: 100mA (ea. Output) Compatible with: SoundTraxx 884010 | Tsunami2 TSU-N18 Steam-2 Digital Sound Decoder SoundTraxx 885026 | Tsunami2 TSU-N18 EMD Diesel Digital Sound Decoder SoundTraxx 885027 | Tsunami2 TSU-N18 GE Diesel Digital Sound Decoder SoundTraxx 885028 | Tsunami2 TSU-N18 ALCO Diesel Digital Sound Decoder SoundTraxx 885029 | Tsunami2 TSU-N18 Baldwin & Other Diesel Digital Sound Decoder SoundTraxx 885030 | Tsunami2 TSU-N18 EMD-2 Diesel Digital Sound Decoder SoundTraxx 886007 | Tsunami2 TSU-N18 Electric Digital Sound Decoder
£11.33
SoundTraxx SoundTraxx 810109 | 20mm Baffle Kit
This snap-together baffle kit is designed for use with our 20mm round speakers (P.N. 810053).
£5.02
SoundTraxx SoundTraxx 810133 | Sunny White LEDs (6-Pack)
Sunny White LED for adding Hyperlight effects or as bulb replacements. 3mm (0.012") diameter 3.3 Volt
£9.43
