Gift Ideas Under $100.00

You haven’t heard WOWSound until you’ve heard it through our 28mm High Bass 4W WOWSpeaker! This speaker handles an unprecedented 4 watts of power, and showcases a mighty bass reflex that packs a big sonic punch. Welcome to the new standard for sound in model trains – pick one up today and prepare to be blown away! This speaker is 28mm (1.1″) diameter and 13.5mm (0.53″) thick which includes a rubberized mounting gasket. The mounting gasket allows for unrestricted movement of the cone, preventing distortion or physical damage! Note: Product listing is for 1x speaker. Additional images provided for clarity. Dimensions: 1.1″ diameter x 0.53″ or 28mm diameter x 13.5mm Sound Pressure Level: 84 ± 3.0 dB (A), at 0.63 V, 0.1 m, Average 500,1,000, 2,000, 4,000 (Hz ), at 25°C Effective Frequency Band: 250 Hz. to 20 kHz. Power Rating: 3W (Typical) 4W (Peak) DC Impedance: 4 Ω ; ± 15%, at 1,000 Hz., 1.0 V

Read more less

Perhaps you are familiar with this scenario: there is a digital decoder sitting on your workbench and you want to test it prior to a perhaps complex installation. But how to do this? The Profi Decoder tester makes it easy for you: simply connect the tester to your command station or the LokProgrammer. It enables you to test any decoder without exposing it to any external factors caused by the locomotive that may influence its performance. Features In order to make things as easy as possible for you, the Profi Decoder Tester is equipped with some useful features. It has all commonly used interface sockets for connecting a decoder for the smaller scale models: Besides a 6-pole NEM 651 socket and the 8-pole NEM 652 socket, it also has an 21MTC interface as per NEM 660, a PluX22 socket as well as a Next18 interface: No matter which type of decoder you have: Simply plug it in – it will fit! And that’s all there is to it! Decoders without any interface can be contacted with individual terminals.  A quality coreless motor with flywheel serves in conjunction with LEDs indicating the direction for checking the motor output: Thus it is quite easy to check on the low speed performance and the even speed of the decoder. An LED monitor informs you about the functioning of the headlights and back-up lights as well as the function outputs AUX1 through AUX6. For testing LokSound decoders we have integrated a 20 mm speaker. You may choose if the integral speaker should be switched off or if it should have 100 Ohm respectively 16 Ohm – thus the Decoder Tester is perfectly suitable for any ESU decoder generation! Two SUSI plugs facilitate the direct test of optional SUSI modules as well as the connection to another circuit board. The electrical connection to either the command station or the LokProgrammer is facilitated by a removable, 2-pole terminal block (same system as used on the LokProgrammer and the ECoS) or via two solder points. The dimensions of the ESU Decoder Tester are 99 x 74 x 34mm. WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

Supply power to your Static King 639 with the Woodland Scenics 641 Field System™ Power Supply. This power supply is a reliable source of energy for your Static King to run smoothly, making it the perfect addition to your collection. Optimizes Static King performance.  

Read more less

Plug this USB module into your PC (Personal Computer) to add Direct Radio to your computer so you can control and setup RailPro products like the RailPro locomotive modules!You can use a CI-1 and a PC to get started with RailPro for a lower cost! You can buy a real RailPro handheld controller at a later time.PC Requirements: Windows 10, Windows 8, Windows 7, and Vista. Product Specifications: Interface: USB-A Dimensions: 1.87 x 0.78 x 0.34 in   Download the CI-1 Software Here!  

Read more less

Static Grass 28 grams Grass length: 12mmm

Read more less

Scenic Cement is a ready-to-use spray or brush-on adhesive specially formulated to glue Ballast, Turf and other landscape materials to a layout. This multi-use product is non-toxic, water-based and dries to a matte finish. It contains a wetting agent that breaks surface tension, allowing easier and faster penetration of scenery materials for a strong bond. It also permeates instantly for maximum coverage. Apply with the Scenic Sprayer™ for a smooth, flowing application that reduces spray head clogging, foaming and bubbles. 16 fl oz (473 mL)

Read more less

The LM-3S is a module that you can install into a model train locomotive so the locomotive can be controlled and setup by a Ring Engineering RailPro Controller, such as the HC-2 Handheld Controller with a Color Touch Screen! After the LM-3S is installed in a locomotive, you will be able to control the locomotive speed, direction, up to 6 light outputs and sounds! The LM-3S has “Direct Radio” (RF transceiver) built inside. The built in RF module allows commands and data to be sent and received to and from the module. You can load a picture of your choice into the LM-3S module. Then you will be able to touch the screen of the HC-2 to take control of your locomotive! You can even download new sounds and light effects using the built in Direct Radio!The LM-3S is electrically compatible with the DCC plug found in many locomotives to promote easy installation. Product Specifications: Sound Profile: Universal (all) Dimensions: 1.50 x 0.68 x 0.25 in DCC Track Voltage: 7.5V – 18V Light Outputs 6   The LM-3 is equipped with Direct Radio! This allows Ring Engineering Controlling Devices such as the HC-2, Handheld Controller with Color Touch screen, to control and configure your locomotive by sending and receiving data directly to the LM-3 through the air by use of RF transmission! The Direct Radio is very fast giving your locomotive quick response to your controls. Further, a controlling device can detect your LM-3 with just a few touches on the screen. Because of Direct Radio, you can load a picture of your locomotive to the LM-3! You can also load Light Effects and much more!Radio Load Sharing is a truly an innovative invention from Ring Engineering. It allows your locomotives that are linked together (sometimes called Consisted or MU'ed) to actually share pulling power. Only RailPro equipped locomotives use Direct Radio to talk to each other to be sure each locomotive pulls its share of the load! Even more amazingly, Ring Engineering's patent pending process only takes seconds to setup!Six light outputs. Can be configured for multiple light effects on a single output including On/Off, Dim, Ditch, Mars, Strobe, and more! Additional light effects can be loaded using DirectRadio!Built in protection with fault reporting by Direct Radio!Tiny size 1.50 x 0.68 x 0.25 Inches for easy fit.

Read more less

#206 Insulated Muti-Purpose Coupler Height Gauge - HO ScaleIncludes the #148 Whisker® Coupler & #158 Scale Whisker® Coupler. - Kit. EASY TO ASSEMBLE & USE A must have tool for gauging mounting height, correct coupler height, trip pin, and permanent uncoupler heights for achieving trouble free coupler performance. Also has a built in HO track gauge. "Takes the guess work out" Four tools in one.1. Provides instant visual reference of proper coupler height.2. Accurately measures proper trip pin height above rail.3. Built-in track gauge. (N.M.R.A. Standard)4. Movable dowel tests Kadee® Magne-Matic® Uncoupler height and registers the needed adjustments.5) Provides instant visual reference of proper body mounting height.Track not included Package Includes: (1) each #148 Whisker® Coupler (1) each #158 Whisker® Coupler (1) each #206 Lid (1) each #206 Dowel (1) each #206 Height Gauge Base (10) each .015 Red Fiber Washers (2) each #622 Knuckle Springs (2) each #625 Knuckle Springs (1) each 2 x 1/4" Screw

Read more less

Red LED Flashing Nano Lights 30mA Includes 24" cables 2 lights per package Ready to plug into Light Hub (sold separately) INSTRUCTIONS: Align locking tabs on Light Plug with front of Light Hub (JP5700, JP5701) and insert into LIGHT Port until locking tabs click into place. Glue or tape Light in place, as required. Pink plastic band (1/2") on cable identifies Red Flashing light.

Read more less