On Sale

HO Scale Metal pole and arms LED lights for low current drain Ready to use with resistors attached Designed for easy mounting Great for use as parking lot lights  2 lights in the package

Read more less

Replacement Pads for Rail Tracker™. Use with Clean Track Solution™ to remove dirt and make track ready for operation. Includes eight Cleaning Pads (dark-colored) and eight Finishing Pads (light-colored). Works for N, HO, HOn3 and three-rail O scale track.

Read more less

The #153 "Scale" All Metal Self-Centering WHISKER® Coupler features a "Scale" Metal Coupler (a smaller head coupler which is more to scale and is patterned after the type 'E" couplers) & Metal WHISKER® Centering Spring, insulated Draft Gear Box and Lid. The #153 Coupler may be mounted with the supplied #242 draft gear box, other Kadee® HO-Scale draft gear box shown below or with the Manufacturers cast-on coupler pockets. The coupler will couple and uncouple with other Kadee® HO and HOn3 couplers. The coupler has the same shank length as the #23, 33 or 43 coupler which will allow the modeler to remove the existing #23, 33 or 43 coupler and replace with the new smaller coupler. The #153 coupler is made of the same metal as the #43 for strength and rigidity. It is not recommended to use a metal coupler directly on a metal surface or in a metal draft gearbox to avoid possible electrical crossover and shorting that may cause damage. Use the provided insulated gearbox. HO-Scale Package Includes: (2) Pair #153 Scale Whisker® Metal Couplers - Short Centerset Shank (2) Pair #242 Snap-Together Gearboxes (2) #625 Knuckle Springs #153 Scale Whisker® Metal Coupler Features: Material  -   Metal Shank Length  -   Short (1/4") (center hole to back of coupler head) Coupler Offset  -  Centerset Knuckle Spring  -   #625 Centering System  -   Whisker® Head  -   Scale Head Works In Place of  -   #23, #33 (#143 in a #252 box), short centerset "clone" couplers Works With  -   #213, #232, #234, #242, #252, #262, manufacturer cast-on draft gearboxes #242 Snap-Together Gearbox Features: Material  -   Insulated Plastic Lid Type  -   Snap-Together Dimensions  -   7/16"L x 5/16"W x 1/8"H Works With  -   NO.5®, #58, 20-Series and 40-Series, All Whisker® Couplers Mounting Specifications: Mounting Height  -   25/64" Centerline  -   25/64" Trip Pin Height  -   1/32" Center Hole  -   2-56 Insulated Screws are the most commonly used. (Screw length will vary) Recommended Tools: #206 Insulated Muti-Purpose Coupler Height Gauge #231 Greas-em Dry Graphite Lubricant #237 Coupler Trip Pin Pliers #240 Double Headed Pin Vise #241 Dual Tool Manual Uncoupling Tool and Spring Pick #246 Tap (2-56) and Drills (#50 and #43)

Read more less

$0.00 Pre-Order | Estimated delivery Fall 2024Guaranteed Pre-Order Due Date: May 30, 2024   Bring big power to your HO railroad with the WalthersMainline SD75M! Built from 1995 to 1996 at the request of the Santa Fe for a higher horsepower unit (4300 versus 4000 for a standard SD70), most were later transferred to the new Burlington Northern & Santa Fe Railway following the 1995 merger, where many are still in service with BNSF. These units were built with the wide North American Safety Cab, thus the "M" (for "modified") in the model designation. Other features include: One time run of these roadnumbers, order now - limited quantity available! Correct North American Safety Cab per prototype Flush radiators per early production units Correct HTCR-1a or HTCR-1b trucks per prototype Brass Nathan K5 air horn Treadplate detail on walkways Minimum radius 18" (22" or larger recommended) Fully assembled LED Lighting includes: 21-Pin DCC plug Same powerful drive as WalthersProto(R) locos featuring: 5-pole skew-wound motor 14:1 gear ratio Helical-cut gears for quiet operation and easy multiple unit operation All-wheel drive and electrical pickup Dual machined brass flywheels Heavy die cast metal chassis Cab interior 5000-gallon fuel tank w/road specific details Standard bell on conductor's side Molded drill starter points for grab irons - easily added with SD70-Series Diesel Detail Kit (910-261, sold separately) Correct size RP-25 metal wheels Proto MAX(TM) magnetic metal knuckle couplers  Road-specific details on this model include: Low headlight HTCR-1a trucks Nose door with window  More Information Item # 11003 Brand WalthersMainline Scale HO Type EMD SD75M Engine Electronics Standard DC Road Name BNSF Railway Road Number 8268 MSRP $169.98

Read more less

This product is versatile in terms of direction of the placement of the board and mounting in various configurations.  It can easily replace a QSI board, a Dual Mode decoder board or be mounted directly on the electric motor or frame with Kapton tape.  (It is recommended that a piece of Kapton tape be placed on the bottom of the mother board to assure electrical isolation from the electric motor or frame.) This mother board does not include a 21 Pin Decoder. This mother board and connector board require soldering. These printed circuit boards are NOT INTENDED FOR USE IN A DC SYSTEM. The on board resistors are sized for LEDs. (2.2K)  Package Includes: 1x Mother Board 1x Connector Board Dimensions: 0.67" x 2.20" x 0.35" (17 mm x 56 mm x 0.9 mm)The mother board includes;  One 21 Pin Decoder receptacle Two pairs of track input pads One pair of motor input pads One pair of stay alive pads (U+ and GND) Two pairs of speaker pads wired in parallel Resistors for use with LED lighting. (on board 2.2K)  The connector board contains pads for eight pairs of lighting function connections. U+ or the blue wire has eight connected pads for the common power source. The negative (-) discrete function pads are all labeled to indicate their connection to the functions available in the decoder. The lighting connector was designed so that the shell of the diesel locomotive can be easily separated from the frame without un-soldering wires. This does require that the headlight and rear lights be mounted in the shell of the locomotive and that the diesel has a removable dynamic brake shell. Incandescent lamps or bulbs are not well suited for the Decoder Buddys or associated decoders.  It can be done but it will require more electronics to achieve a result.  Our recommendation is to go with LEDs.

Read more less

Enjoy complimentary shipping! Bundle your purchases for even more savings with our free shipping option. (This offer is optional) Providing enough steam to power train heat and some air conditioning systems on postwar trains taxed the standard water supply of EMD F7 A units set-up for passenger service, prompting EMD to roll out the new FP7 in 1949. Though outwardly similar to the F7A, FP7s were actually four feet longer to accommodate bigger water tanks with a capacity of 950 US gallons. Standard passenger power into the Amtrak era and beyond (with some also handling freight chores), these WalthersProto replicas are fully assembled and ready for service with: One time run of these roadnumbers, order now - limited quantity available! Matches the prototypes' extended frame and body Railroad-specific details Five-pole, skew-wound, high-torque, high-efficiency can motor Helical gears with 14:1 ratio for smooth, ultra-quiet running Easy multiple-unit operation Correct RP-25 wheelsets Proto MAX(TM) magnetic metal knuckle couplers Road-specific details of this WalthersProto replica include: A unit details - Nathan M5 Air horn w/all bells forward Whip-style radio antenna w/conduit Freight pilot Knob-style sand hatch doors Late water filler Cab wind deflectors Etched-metal cab sunshades Standard type winterization hatch Vertical body louvers Photo-etched Farr vertical grilles Dual headlights - upper single, lower twin vertical More Information Item # 920-49546 Brand WalthersProto Scale HO Engine Electronics DC, DCC Ready Type EMD Diesel Road Name Chesapeake & Ohio Road Number 8005 & 8505 Estimated Release Date June 2024

Read more less

Power your HO railroad's flagship streamliners with these superb replicas of EMD's famed E8 and E9 diesels. Introduced in 1948 with the new 567B prime mover, production contiued until 1954 when the virtually identical E9 was introduced with the more powerful 567C prime mover. Powerful, reliable and economical, EMD E units handled premiere long-distance trains for decades, with many ending their long careers in commuter service and ocassionally handling fast freight trains. Fully assembled and ready for service, features include: One time run of these roadnumbers, order now - limited quantity available! Road- and era-specific details Rugged and reliable WalthersProto drive 21-pin DCC plug Formed wire grab irons and handrails Photo-etched lift rings Cab interior w/seats and figures All-wheel drive and electrical pickup Constant and directional LED lights Correct size RP-25 metal wheels Proto MAX(TM) metal knuckle couplers Road-specific features of this WalthersProto replica include: Nathan five-chime (all forward) air horn Single horizontal sealed-beam headlight Working backup light Flush number boards Removed skirts Freight pilot Southern-style MU bracket 4-hose MU set at left and right Photo-etched E8A-style Farr air grilles Dynamic brake with 48" fan Winterization hatches w/levers Single offset steam generator Rooftop air reservoirs w/piping Round spark arrestors Rectangular air vent Roller bearing sideframes Wheel slip hubs Speed recorder Southern-style left and right water tanks More Information Item # 920-49922 Brand WalthersProto Scale HO Engine Electronics DC / DCC Ready Type EMD Diesel Road Name Southern Road Number 6900

Read more less

The Walthers Cornerstone HO Scale 90' Turntable is based on those used at small steam engine terminals. A vital part of train operations, this kit has ben carefully designed to fit most layouts and the 90' turntable has a one-piece pit for drop-in mounting. Once assembled, the bridge is manually position able. The kit includes the pit, gear drive, realistic decals and complete instructions. Complete hookup instructions cover wiring, adding track and more. The detailed bridge includes the operator's cab, handrails and a traditional arch (used to supply electrical power to the drive motors on the prototypes). This model can be motorized by adding Motorizing Kit 933-1050 (sold separately). The 90' Turntable is one of many Cornerstone HO Scale railroad buildings. Centerpiece for a small locomotive servicing area Manually position able Can be motorized by adding Motorizing Kit 933-1050 (sold separately) Molded in appropriate colors

Read more less

Handle fast freight on your HO railroad with the rugged WalthersProto SD45! Introduced in 1966 with a 20-cylinder 645 prime mover cranking out 3600 horsepower, SD45s quickly became the preferred power for expedited freights and piggyback trains, going on to new careers with regionals and shortlines into the 1980s and beyond. Ready for service, features of these WalthersProto replicas include: NEW - High, short hood versions of Norfolk & Western & Southern Railway units One time run of these road numbers, order now - limited quantity available! Prototypes in freight service from 1966 to early 2000s - several preserved today! Road-specific details DCC-ready with 21mtc plug Superb paint and lettering Five-pole, skew-wound, high-torque, high-efficiency can motor Helical gears with 14:1 ratio for smooth, ultra-quiet running LED constant and directional headlights as appropriate Easy multiple-unit operation Heavy die-cast metal underframe Correct size RP-25 metal wheels Proto MAX(TM) metal knuckle couplers Road-specific details on this model include: NEW - High short hood Leslie S-5T-R air horn Firecracker radio antenna Long hood forward operation Hood-mounted walkway lights (nonworking) Long hood mounted bell and bracket Flexicoil-C trucks with high-mount brake cylinders

Read more less

This set includes five officers and one canine cop. A full-figured officer is eating a doughnut, while another is writing a ticket. With gun in hand, an officer is ready to draw. One is directing traffic, and another is walking his beat, smacking a nightstick into his open hand. Set contains 6 pieces. Colors may vary from actual product. Complete your scene and bring it to life with affordable works of art in HO scale. Sculpted in fine detail and hand-painted, they add color, humor and interest to any layout. Scenic Accents figures have a natural charm and a realistic appearance that steal the show! Economy packages also available in HO scale. Attach with Scenic Accents Glue and position with Gentle Grips®.

Read more less

N Scale Metal Pole and arm Led Light with low current drain Ready to use with resistor attached Designed for easy mounting

Read more less

HO Scale Metal Pole and arm Led Light with low current drain Ready to use with resistor attached Designed for easy mounting

Read more less