CouponAd-NoMAP
ESU LLC ESU 41010 | Premium Foam Train Service Tray | 328x 166 x 68 mm | With magnetic storage recess | HO Scale
The ESU Premium Foam Train Service Tray is the ideal tool for the maintenance and care of your locomotives. Two recesses are available for perfect work: The locomotive can be clamped upside down to comfortably reach the underbody of the locomotive. In the classic inclined tray, you can easily reach the sidewalls of the locomotive or set up the locomotive almost vertically, in order to achieve the interior of the locomotive well. The Premium Foam Train Service Tray consists of a soft, fine-pored foam with high restoring force. As a result, small parts such as handle bars, antennas or pantographs cannot get caught and thus reduce the possibility of damage to a minimum. The material is resistant to oil, grease and other cleaning agents. For safe storage of small parts and screws, a magnetic storage recess is available over the entire length. The Premium Foam Train Service Tray is 328mm long and can be arranged in rows, so that longer Service Trays for the maintenance of railcars can be built. WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov
$22.29
ESU LLC ESU 50342 | Rectangular Speaker with Enclosure - 8 Ohm, 1/2 Watt, 11/32 x 1/2 x 1/8" 9 x 13 x 3mm | Multi Scale
The LokSound by ESU Rectangular Speaker with Enclosure is ideal for use in N, TT and small HO Scale model locomotives. This speaker includes a built-in enclosure to enhance its output and is rated at 8 Ohms and 5 Watts. At only 11/32 x 1/2 x 1/8" 9 x 13 x 3mm, this tiny speaker will easily fit inside widely used narrow-hood diesels such GPs, SDs, GE U-Boats or GEVO diesels as well as other locomotives. More Information Item # 50342 Brand ESU Scale N & HO MSRP 10.99 WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov
$9.29
ESU LLC ESU 50343 | Rectangular Speaker with Enclosure - 8 Ohm, 1-1/8 x 2-21/32 x 9/16" 29 x 68 x 14mm | Large Scale
The LokSound by ESU Rectangular Speaker with Enclosure is ideal for use in G, I and O Scale model locomotives. This speaker includes a built-in enclosure to enhance its output and is rated at 8 Ohms. At 1-1/8 x 2-21/32 x 9/16" 29 x 68 x 14mm, this speaker will easily fit inside your favorite large-scale locomotives. More Information Item # 50343 Brand ESU Scale Large: G & O WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov
$18.59
ESU LLC ESU 50344 | Rectangular Speaker with Enclosure - 8 Ohm, 15/16 x 2-5/32 x 11/32" 24 x 55 x 8.6mm | Multi Scale
The LokSound by ESU Rectangular Speaker with Enclosure is ideal for use in HO, OO, S and small O Scale model locomotives. This speaker includes a built-in enclosure to enhance its output and is rated at 8 Ohms. At 15/16 x 2-5/32 x 11/32" 24 x 55 x 8.6mm, this rectangular speaker will easily fit inside your favorite locomotives. More Information Item # 50344 Brand ESU Scale Multi WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov
$13.65
ESU LLC ESU 50345 | Rectangular Speaker with Enclosure - 4 Ohm, 7/8 x 1-21/32 x 5/16" 22 x 42 x 8mm | Multi Scale
The LokSound by ESU Rectangular Speaker with Enclosure is ideal for use in model locomotives as a replacement for a 20 x 40mm speaker. With the help of the built-in passive radiator in conjunction with two rectangular speakers, the module achieves a significantly improved bass response and achieves a considerable sound pressure even at the high and mid-range. The module is particularly suitable for diesel or steam locomotives, where emphasis is placed on contemporary bass reproduction. This speaker includes a built-in enclosure to enhance its output and is rated at 4 Ohms. This rectangular speaker measures 7/8 x 1-21/32 x 5/16" 22 x 42 x 8mm. More Information Item # 50345 Brand ESU Scale Multi WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov
$13.65
ESU LLC ESU 50346 | Rectangular Speaker with Enclosure - 8 Ohm, 15/16 x 2-5/32 x 11/32" 24 x 55 x 8.6mm | Multi Scale
This loudspeaker module is suitable for large tenders with gauge H0 or OO or models with gauge 0. Its built-in passive radiator, in conjunction with the built-in broadband speaker, results in good bass reproduction without neglecting the highs and mids. Especially for diesel or steam locomotives, this module is a real alternative for those who like deep bass but don't need extreme volume. The speaker fits perfectly with our LokSound 5 or LokSound 5 L decoders. More Information Item # 50346 Brand ESU Scale HO, O & G MSRP 17.99 WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov
$13.65
ESU LLC ESU 50347 | Rectangular Speaker with Enclosure - 8 Ohm, 7/8 x 1-21/32 x 5/16" 22 x 42 x 8mm | Multi Scale
This new speaker module fits wherever 20mm x 40mm rectangular speakers were previously installed. With the help of the built-in passive radiator in conjunction with a high-performance rectangular speaker, the module achieves significantly improved bass reproduction and achieves a considerable sound pressure even in the highs and mids. The module is particularly suitable for diesel or steam locomotives where contemporary bass reproduction is important. The speaker fits perfectly with our LokSound 5 micro, LokSound 5 or LokSound 5 L decoders. More Information Item # 50347 Brand ESU Scale HO, O & G MSRP 17.99 WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov
$13.65
ESU LLC ESU 51831 | SwitchPilot 3 Plus Accessory Decoder - For 8 Accessories | Multi Scale
SwitchPilot 3 Plus decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other stationary consumption. In order to facilitate the rather cumbersome configuration of magnetic article decoders, the SwitchPilot 3 Plus has an innovative operating concept consisting of a 4-line, illuminated OLED display and three input buttons. Modes The SwitchPilot 3 Plus is multi-protocol and can be used with control panels according to the Märklin® Motorola® system (e.g. 6021, Central Station® or Mobile Station®) as well as DCC-enabled control panels. The configuration can take place on both the main track and the programming track. Thanks to RailCom®, CVs can also be read out. Functioning The SwitchPilot 3 Plus can be supplied directly from the digital system or from an external DC or change voltage source. It has a total of 16 transistor outputs, which are grouped in the 8 exit pairs 1 to 8. Each output pair contains two outputs (OutA and OutB) and can be configured individually for the desired use case: In pulse mode, the output is switched on as soon as a switching command is received. Since the output automatically switches off again as soon as a time stored in the decoder has been reached, a burn-through of magnetic articles is prevented. At the moment (K83-compatible) the output remains active as long as the button on the control panel is pressed. This operating mode is suitable for turnout drives with final shutdown or for de-caps. In bi-stable continuous operation (k84-compatible), the two outputs are switched on and off: When pressing the first button (red) on the control panel, the output Out A is switched on. It remains active until pressing the assigned button (green) activates the output Out B of the same output group. Out A and Out B behave like a change switch.In alternating flasher mode, the outputs Out A and Out B of an output pair are switched on alternately with an adjustable flashing frequency. The change indicator is started with the command "Gerade/Green" of the assigned button and stopped again with the command "Branching/Red".Optionally, the output can also be slowly dimmed and dimmed (so-called "zoom" for incandescent lamp simulation). Set The SwitchPilot 3 Plus can be flexibly adjusted either on the programming track with DCC control panels or on the main track with POM ("Programming on Main") or can also be read out via RailCom® CVs. On request, he also learns the addresses directly via a programming button. The setting is, of course, the simplest with the integrated OLED displays as well as the three input buttons: All (!) Settings can be checked directly on the decoder and changed on request. "Programming" with the help of your headquarters is not required. It really can't be any easier. The ESU LokProgrammer can be used for firmware updates. Protection As with our locomotive decoders, the outputs of the SwitchPilot 3 Plus are protected against overload. We want you to enjoy your decoder for as long as possible. More Information Item # 51831 Brand ESU Scale Multi WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov
$68.25
ESU LLC ESU 51840 | SignalPilot Accessory DCC Decoder for Signals | Multi Scale
SwitchPilot 3 decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other stationary consumption.In order to facilitate the rather cumbersome configuration of magnetic article decoders, the SwitchPilot 3 has an innovative operating concept consisting of a 4-line, illuminated OLED display and three input buttons. Modes The SwitchPilot 3 is multi-protocol and can be used with workstations according to the Märklin® Motorola® system (e.g. 6021, Central Station® or Mobile Station®) as well as DCC-enabled control panels. The configuration can take place on both the main track and the programming track. Thanks to RailCom®, CVs can also be read out. Functioning The SwitchPilot 3 can be supplied directly from the digital system or from an external DC or change voltage source. It has a total of 8 transistor outputs, which are grouped in the 4 exit pairs 1 to 4. Each output pair contains two outputs (OutA and OutB) and can be configured individually for the desired use case:In pulse mode, the output is switched on as soon as a switching command is received. The fact that the output automatically switches off again as soon as the time stored in the decoder has elapsed prevents the burning of magnetic article drives.At the moment (K83-compatible) the output remains active as long as the button on the control panel is pressed. This operating mode is suitable for turnout drives with final shutdown or for de-caps.In bi-stable continuous operation (k84-compatible), the two outputs are switched on and off: When pressing the first button (red) on the control panel, the output Out A is switched on. It remains active until pressing the assigned button (green) activates the output Out B of the same output group. Out A and Out B behave like a change switch.In alternating flasher mode, the outputs Out A and Out B of an output pair are switched on alternately with an adjustable flashing frequency. The change indicator is started with the command "Ge- rade/Green" of the assigned button and stopped again with the command "Branching/Red".Optionally, the output can also be slowly dimmed and dimmed (so-called "zoom" for glow lam pen simulation).With the switch 3 mode switch, you can switch all output pairs together to the "k83" or "k84" modes at lightning speed, regardless of how they are configured. Feedback Since the SwitchPilot 3 is RailCom®-capable, all settings can be read out and changed directly in the built-in state on request. In combination with an ECoS as an ideal "partner", the SwitchPilot 3 can record and display the actual turnout setting with appropriately prepared turnout drives. Finally, you have the certainty that your switch has switched correctly! Set The SwitchPilot 3 can be flexibly adjusted either on the programming track with DCC control panels or on the main track with POM ("Programming on Main") or can also be read out via RailCom® CVs. On request, he also learns the addresses directly via a programming button. The easiest way to set is, of course, with the integrated OLED display and the three input buttons: All (!) Settings can be checked directly on the decoder and changed on request. A"Programming" with the help of your control panel is not required. It really can't be any easier. The ESU LokProgrammer can be used for firmware updates. Protection As with our locomotive decoders, the outputs of the SwitchPilot 3 are largely protected against overload. We want you to enjoy your decoder for as long as possible. More Information Item # 51840 Brand ESU Scale Multi WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov
$68.25
ESU LLC ESU 51993 | 18-Pin Next18 Socket-to-Wire Leads Harness LokSound | Multi Scale
3-7/16" 8.8cm Wire Leads, Includes Heat-Shrink Tubin Wire harness, 18-pin Next18 socket to open wires, 88mm, with heat shrink tube. WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov
$6.09
ESU LLC ESU 51995 | 18-Pin Next18 Socket-to-NEM652 8-Pin Adapter Board | Multi Scale
Adapter board, 18-pin Next-18 socket to NEM652 8-pin, Flex, 88mm, with heat shrink tube WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov
$6.59
ESU LLC ESU 53452 | LokProgrammer unit, US 110V power supply, manual, USB adapter (Dimensions: 95mm x 85mm x 22mm (3.74 inch x 3.35 inch x 0.87 inch) | Multi Scale
You want to listen to the sound spectrum of your favourite loco, or the special sound of that loco around the corner in the yard – on your model railroad? No problem with ESU’s LokProgrammer! One prerequisite: A PC with sound card and Windows (Windows 8.1 and higher). Simply record the original sound of your engine and edit it at home with your computer. Many customers did this already successfully. Even if you don’t yet belong to this elite group of LokSound Pro’s, the LokProgrammer is still a very useful tool for you. It is the easiest way to program your ESU-decoder. You need no programming experience, thanks to the graphic screen everything falls into place with a few mouse clicks. What the LokProgrammer can do: Change the sound safed on the decoder. Setting of all digital parameters of the Loksound decoder such as address of the loco, operation speed, maximum speed, braking deceleration, brightness of bulbs etc; you can set all options with your computer very easily - no cumbersome entering of CVs (configuration variables) with your command station. Rearrange your sounds and transfer it to the LokSound decoder. You can use all sounds that can be downloaded to your computer hard disk. Sound can be allocated to different events. Additional sounds can be activated via function buttons. Sound With the LokProgrammer you can erase the sound data of any LokSound decoder as many times as you wish, and replace it with a different sound. To this end we offer on our homepage more than 200 different, fully matching sounds of various prototypes and locos for downloading on your computer. Also you can edit just parts of a sound project: You don’t like the decoder’swhistle? Just replace it with one of the many others. Suitable sources beside those offered by us, are in Windows *.wav format available. Sound – even voice or music is no problem for our decoders. With the LokProgrammer’s aid you use the entire flexibility and functionality offered by LokSound decoders. Programming By the same token, all other ESU decoders profit from the LokProgrammer’s versatility; no matter if DCC, Multiprotocol - or mfx decoder. With its help it’s possible to edit all parameters of the particular decoder simply and conveniently. The available options depend on the kind of decoder. Beside addresses and acceleration - and deceleration settings, this concerns above all the allotment of function keys (function mapping), the allocation of special effects to the individual outputs, or the lamp brightness. The LokProgrammer can also help when optimizing back EMF parameters or the loadable speed table. All options can be programmed very conveniently: There is no tedious punching-in of CV-numbers at the digital station anymore. Hook up It’s this simple: The LokProgrammer is a small programming box, which is wired between the PC and a programming track. To connect it you need either a vacant serial interface, or you use the included USBadapter cable (works with Windows up to Windwos 10). For power we include a 500 mA wall power supply. If your needs are greater (e.g. for gauge I engines), you can also use a conventional model railroad transformer. Software After hook-up you start up the especially user-friendly LokProgrammer software. This runs on all modern Windows-systems (Windows 8.1 and higher). Just put the loco with the ESU decoder on your programming track, and right away you can read, edit or program it. The Programmer automatically recognizes the decoder in the engine. Simplicity The LokProgrammer is recommended not only for the use with our ESU decoders: By now, many well known model railroad manufacturers factory-furnish their locos with ESU-decoders, which of course can be modified again within the frame work of their technical specifications – with the help of the LokProgrammer. You see, purchasing a LokProgrammer pays off in any case. Upgrades The LokProgrammer can also be instrumental in updating decoders. Almost all ESU decoders are updatable, in case you desire a new software version. To do this, you only need the LokProgrammer and a small update-program, which you can download from our homepage. The future LokProgrammer software is being reviewed continuously. The latest, pertinent version can always be downloaded from our homepage, or can be installed automatically, through an internet-update function, on your computer. More Information Item # 53452 Brand ESU Scale Multi
$140.39
