The LM-4S-G is a module that you can install into a model train locomotive so the locomotive can be controlled and setup by a Ring Engineering RailPro Controller, such as the HC-2 Handheld Controller with a Color Touch Screen! After the LM-4S-G is installed in a locomotive, you will be able to control the locomotive speed, direction, up to 6 light outputs and sounds! The LM-4S-G has “Direct Radio” (RF transceiver) built inside. The built in RF module allows commands and data to be sent and received to and from the module. You can load a picture of your choice into the LM-4S-G module. Then you will be able to touch the screen of the HC-2 to take control of your locomotive! You can even download new sounds and light effects using the built in Direct Radio! Product Specifications: Sound Profile: Universal (all) Dimensions: 3.35 x 1.32 x 0.57 in DCC Track Voltage: 7.5V – 18V Light Outputs 6   Package Contents: LM-4S-G Locomotive Module WH-9 9 Pin Wiring Harness Instruction Sheet The LM-4S-G is equipped with Direct Radio! This allows Ring Engineering Controlling Devices such as the HC-2, Handheld Controller with Color Touch screen, to control and configure your locomotive by sending and receiving data directly to the LM-4S-G through the air by use of RF transmission! The Direct Radio is very fast giving your locomotive quick response to your controls. Further, a controlling device can detect your LM-4S-G with just a few touches on the screen. Because of Direct Radio, you can load a picture of your locomotive to the LM-4S-G! You can also load Sounds, Light Effects and much more!Your LM-4S-G is equipped with Rail Sonic HD Sound System! This is Ring Engineering's technology that allows your LM-4S-G to produce realistic locomotive sounds!Radio Load Sharing is a truly an innovative invention from Ring Engineering. It allows your locomotives that are linked together (sometimes called Consisted or MU'ed) to actually share pulling power. Only RailPro equipped locomotives use Direct Radio to talk to each other to be sure each locomotive pulls its share of the load! Even more amazingly, Ring Engineering's patent pending process only takes seconds to setup!Six light outputs. Can be configured for multiple light effects on a single output including On/Off, Dim, Ditch, Mars, Strobe, and more! Additional light effects can be loaded using DirectRadio!Built in protection with fault reporting by Direct Radio!Tiny size 3.35 x 1.32 x 0.57 Inches for easy fit. Important: If you are running your trains outside be sure to buy the model HC-2-SUN handheld controller instead of the standard model HC-2. The HC-2-SUN is easily readable in sunlight.  The HC-2 screen was designed for indoor use and looks real good inside.  Outside the standard HC-2 screen can look washed out when the sun shines on it.

Read more less

HO-scale, 4-function decoder that measures 74 x 17 x 3mm designed to replace the existing manufacturer light board in Atlas HO diesel models, some InterMountain Railway models, and those using a similar physical design. This decoder will operate in both DC and DCC. Dimensions: 74 x 17 x 3mm Max. Motor Stall Current: 1A Max. Function Current: 100mA (each output) Function Outputs: 4 DCC Track Voltage: 21 Volts Maximum

Read more less

HO-scale, 4-function decoder that measures 25 x 16 x 6mm with a 9-pin ‘universal’ JST wiring harness that is mostly used in older pre-DCC or brass models. This decoder will operate in both DC and DCC. Product Specifications: Dimensions: 25 x 16 x 6mmMax. Motor Stall Current: 1AMax. Function Current: 100mA (each output)Function Outputs: 4DCC Track Voltage: 21 Volts Maximum

Read more less

The LM-3S is a module that you can install into a model train locomotive so the locomotive can be controlled and setup by a Ring Engineering RailPro Controller, such as the HC-2 Handheld Controller with a Color Touch Screen! After the LM-3S is installed in a locomotive, you will be able to control the locomotive speed, direction, up to 6 light outputs and sounds! The LM-3S has “Direct Radio” (RF transceiver) built inside. The built in RF module allows commands and data to be sent and received to and from the module. You can load a picture of your choice into the LM-3S module. Then you will be able to touch the screen of the HC-2 to take control of your locomotive! You can even download new sounds and light effects using the built in Direct Radio!The LM-3S is electrically compatible with the DCC plug found in many locomotives to promote easy installation. Product Specifications: Sound Profile: Universal (all) Dimensions: 1.50 x 0.68 x 0.25 in DCC Track Voltage: 7.5V – 18V Light Outputs 6   The LM-3 is equipped with Direct Radio! This allows Ring Engineering Controlling Devices such as the HC-2, Handheld Controller with Color Touch screen, to control and configure your locomotive by sending and receiving data directly to the LM-3 through the air by use of RF transmission! The Direct Radio is very fast giving your locomotive quick response to your controls. Further, a controlling device can detect your LM-3 with just a few touches on the screen. Because of Direct Radio, you can load a picture of your locomotive to the LM-3! You can also load Light Effects and much more!Radio Load Sharing is a truly an innovative invention from Ring Engineering. It allows your locomotives that are linked together (sometimes called Consisted or MU'ed) to actually share pulling power. Only RailPro equipped locomotives use Direct Radio to talk to each other to be sure each locomotive pulls its share of the load! Even more amazingly, Ring Engineering's patent pending process only takes seconds to setup!Six light outputs. Can be configured for multiple light effects on a single output including On/Off, Dim, Ditch, Mars, Strobe, and more! Additional light effects can be loaded using DirectRadio!Built in protection with fault reporting by Direct Radio!Tiny size 1.50 x 0.68 x 0.25 Inches for easy fit.

Read more less

This kit includes all the necessary electronics to add sound, motor, and light control to your G scale locomotive and will allow control with analog (DC) power supply. It also has magnet pickup so you can place magnets in your track for the purpose of playing a sound or turning on a light effect when the train goes over the magnets. Further you can Radio Control a locomotive with this kit installed if you obtain a RailPro handheld controller. You can download new sounds and light effects using the built in Direct Radio!  You can use the Ring Engineering Computer Interface (CI-1) and Ring Engineering PC Software to change the sounds and other settings. Programming the Locomotive ModuleYou can use the Ring Engineering Computer Interface (CI-1) and Ring Engineering PC Software to change the sounds and other settings. The CI-1 is a USB dongle that adds RailPro Radio Communication to a PC.Sounds such as the bell, horn, primemover etc, can be changed.Settings like acceleration, deceleration, and much more can be changed too!There is no need to remove the shell of the locomotive or the need for a programming cable because the changes are made by radio control!   Package Contents: LM-4S-G Locomotive Module MPM-1 Magnet Pickup Module Two Track Magnets Speaker Wiring Harness Instruction Manual   Frequently Asked Questions Is the kit preprogrammed?    Yes.  The RAKS-1 is preprogrammed with diesel sounds. So you can wire in the kit per the user manual instructions and operate your locomotive. However, it is recommended to buy a computer interface and set the motor full load current.  Please see user manual for more details about motor full load current.  Can I use any analog power supply?    No.  You should only use the power supplies that we tested to be compatible with RAKS kit.  There is a link below to the list of power supplies that we tested and found to work with RailPro.PowerSuppliesTestedWithRailProLocomtiveModules.htm  Can the RAKS be used for steam locomotives?    Yes.  The RAKS-1 is preprogrammed with diesel sounds so you will need to buy a Computer Interface to change the sounds to steam sounds.  Please see RailPro Assistant and the Computer Interface user manual for more details about motor full load current.  Can I control a locomotive with a RAKS-1 kit installed by radio control?    Yes.  After the kit is installed so that it can be run by analog, you can just buy a RailPro handheld and control the locomotive by Radio Control!!!  Steps to run a locomotive by radio control:  1) Turn the power up on the analog controller.  2) Press Find Product on the handheld controller to load a picture of the locomotive to the handheld controller.  3) Touch the picture of the locomotive to operate it. See user manuals for complete details. Will the included speaker fit in all G scale locomotives?    No.  The included speaker can be used in many popular G scale locomotives.   Can I use my own speaker with the RAKS-1?    Yes.  Many popular G scale speakers will work fine with the locomotive module.  Please see the locomotive module user manual for details on what speakers are ok to use.   Can you install RailPro locomotive modules in older non-DCC ready locomotives? YES.  You can wire in a RailPro module to most G Scale locomotives including ones that were not originally DCC ready.  If your locomotive is non-DCC, you will need to be sure to isolate the motor from the track pickup and be sure that that final wiring is as shown in the locomotive user manual.     

Read more less

The LM-3 is a module that you can install into a model train locomotive so the locomotive can be controlled and setup by a Ring Engineering RailPro Controller, such as the HC-2 Handheld Controller with a Color Touch Screen! After the LM-3 is installed in a locomotive, you will be able to control the locomotive speed, direction, up to 6 light outputs! The LM-3 has “Direct Radio” (RF transceiver) built inside. The built in RF module allows commands and data to be sent and received to and from the module. You can load a picture of your choice into the LM-3 module. Then you will be able to touch the screen of the HC-2 to take control of your locomotive!The LM-3 is electrically compatible with the DCC plug found in many locomotives to promote easy installation. Product Specifications: Sound Profile: Universal (all) Dimensions: 1.50 x 0.68 x 0.25 in DCC Track Voltage: 7.5V – 18V Light Outputs 6   The LM-3 is equipped with Direct Radio! This allows Ring Engineering Controlling Devices such as the HC-2, Handheld Controller with Color Touch screen, to control and configure your locomotive by sending and receiving data directly to the LM-3 through the air by use of RF transmission! The Direct Radio is very fast giving your locomotive quick response to your controls. Further, a controlling device can detect your LM-3 with just a few touches on the screen. Because of Direct Radio, you can load a picture of your locomotive to the LM-3! You can also load Light Effects and much more!Radio Load Sharing is a truly an innovative invention from Ring Engineering. It allows your locomotives that are linked together (sometimes called Consisted or MU'ed) to actually share pulling power. Only RailPro equipped locomotives use Direct Radio to talk to each other to be sure each locomotive pulls its share of the load! Even more amazingly, Ring Engineering's patent pending process only takes seconds to setup!Six light outputs. Can be configured for multiple light effects on a single output including On/Off, Dim, Ditch, Mars, Strobe, and more! Additional light effects can be loaded using DirectRadio!Built in protection with fault reporting by Direct Radio!Tiny size 1.50 x 0.68 x 0.25 Inches for easy fit.

Read more less

HO-scale, 2-function decoder that measures 17 x 17 x 7mm in a plug-and-play format suitable for use with a variety of models. It is manufactured with an NMRA compatible 8-pin ‘direct-plug.' This decoder will operate in DCC only. Dimensions: 17 x 17 x 7mm Max. Motor Stall Current: 1A Max. Function Current: 100mA (each output) Function Outputs: 2 DCC Track Voltage: 21 Volts Maximum

Read more less

Upgrade your model trains with the Digitrax SDXH167D series 7 sound decoder for HO Scale. Expertly designed with advanced technology, this decoder delivers clear and realistic sound effects for an immersive experience. Enjoy precise control and enhanced functionality with this top-notch decoder. 8 CV-Selectable Steam & Diesel Sound Schemes Included Mobile Decoder with SoundFX v3 Fits many HO locomotives Digitrax 9-Pin Harness Motor 1.0 Amp/2 Amps Peak 6 FX3 Functions, 200ma Output New sound .spjs loadable with Digitrax USB programmer 10-Pin sound harness with 8 Ohm 16 x 26 x 9mm Box Speaker 300uF Capacitor More Information Item # SDXH167D Brand Digitrax Scale HO Scale MSRP $59.00 TCA Grading C-10 Mint - Brand New Availability In-Stock/Restockable Manuals Instruction Sheet

Read more less

TCS Keep-Alive® (KA) devices are used to supply power to decoders during times of power interruption due to dirty track or problematic track work. Newly-redesigned and coming in at half the size of a KA3, the KA1 will power HO or N scale locomotives with approximately one-third of the capacitance of KA3/KA4 devices (depending on the locomotive and motor).This Keep-Alive® includes a Blue and a Black w/ White Stripe wire to attach it to a decoder.

Read more less