DCC Accessories
SoundTraxx SoundTraxx 810109 | 20mm Baffle Kit
This snap-together baffle kit is designed for use with our 20mm round speakers (P.N. 810053).
£5.17
SoundTraxx SoundTraxx 810133 | Sunny White LEDs (6-Pack)
Sunny White LED for adding Hyperlight effects or as bulb replacements. 3mm (0.012") diameter 3.3 Volt
£9.72
ESU LLC ESU 54671 | PowerPack Mini for LokPilot V4.0, LokSound V4.0, LokPilot 5 family and LokSound 5 family, 1F/2.7V | Multi Scale
The new ESU PowerPack Mini can be wired to all fourth and fifth generation ESU decoders. It reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders. With its energy storage (1 Farad capacity) the unit supplies power to all light and motor functions as well as to the sound module. Subject to the energy consumption of your model it may continue to move for up to three seconds. The PowerPack Mini incorporates an integral charging circuit controlled by the decoder. Therefore it may be connected even during programming. In order to avoid an undue load on the booster in case there are several models in the same booster sector, the charging current is limited. The buffer time can be reduced by means of a CV. This may be useful to assure the correct stopping position ahead of signals showing the “Stop” aspect (red signal). Although it is considerably smaller than its predecessor, the space requirements of the PowerPack Mini of about 15.7 mm x 9.7 mm x 13 mm must be taken into account when installing this unit. A three-pole wire harness connects the PowerPack Mini to the decoder. The wires are already soldered to the PowerPack Mini and must be soldered to the appropriate solder pads of the decoder. More Information Item # 54671 Brand ESU Scale Multi WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov
£31.52
SoundTraxx SoundTraxx 810161 | Cool White LEDs (6 Pack) | Multi Scale
Cool White LEDs for adding or using the Hyperlight lighting effects. Can be used as LED replacements or in place of bulbs (see your decoder manual). The cathode or minus (-) side is indicated by the ‘flag’ inside the LED, or by the shorter of the two leads. Dimensions: 3mm (0.12”) diameterVoltage: 3.3 Volts
£9.72
Ring Engineering Ring Engineering PBM-2 RailPro Power Backup Module
A PBM can be added to a HO model train locomotive so that if the model train wheels loose connection from the track because of dirty track or other problems, the Power Backup Module will supply power to the Locomotive Module for up to many seconds to keep operating properly without sounds, lights, or even motor stopping! What is special about the RaiPro PBM is that the PBM is an active power backup not a passive one like many other power backups. Many others are basically just super capacitors that the voltage drops exponentially as soon as the power is removed. With other backups, lights continually dim and module performance is effected. Our PBM has onboard microcontroller and other electronics that will output a fixed voltage similar to a good power supply output so lights stay constant while PBM is active and locomotives perform better. Product Specifications: Connection 2-wire Dimensions: 1.27 x 0.66 x 0.32 in DCC Track Voltage: 12.6V – 16V Approximate Run time lights only: ~18 SecondsApproximate Run time lights and sounds: ~14 SecondsApproximate Run time lights, sounds, and pulling a train:Varies greatly depending on locomotive, speed, load etc. PBM Frequently Asked Questions What is the most important aspect of a power backup module? In our opinion, the most important aspect of a PBM is its ability to power a locomotive pulling a train across dead track. Our PBM works so well that one of our locomotives pulled twelve cars across thirty inches of dead track without stopping while the lights and sounds were on! We tested some other super capacitor only power backup products that only covered a small fraction of the distance and were as large as our PBM! If the most important aspect is powering the locomotive pulling a train, why is there so many others that show or talk about the time the lights stay on? Powering a train can take many times the power then to just have light and/or sounds on because the motor can use much more power than powering the lights and/or sounds. We have seen super capacitor only designs that have real long light on time but when you try to pull a train the results were very poor. One product we tested had many seconds of light and/or sound on time but when pulling a train it died in less than 0.2 seconds! This is why we think many talk about or show light on time because it makes their products look better than they may perform when actually pulling a train. Do I have to use a PBM in all my locomotives for them to run well? NO. If your layout is powered by a RailPro power supply, you have quality locomotives, your layout is properly wired, and you do a reasonable job of keeping your track and locomotive wheels clean, you can have a good running layout without PBMs. So who does Ring Engineering sell PBMs for if some RailPro customers do not really need them? There are many RailPro customers that run on other peoples layouts (like at train clubs) and they cannot control how clean or maintained the track is. There are some RailPro customers that do clean their track regularly but just want extra insurance to be sure they get the best operation possible. Is it ok to use other companies power backup like devices with RailPro locomotive modules? No. Ring Engineering products should only be used as described in their user manuals. The LM user manuals do not say it is ok to connect super capacitors. Using our products in a way not in compliance with our user manuals will void the warranty of the Ring Engineering product and may cause serious problems. There is no public specification on how to design power backup units so there is no guarantee of compatibility. We believe that some regular super capacitor designs have been used with RailPro LM modules and damaged the RailPro modules. If you want power backup you should only use a Ring Engineering PBM with your RailPro locomotive modules. If a power backup has more Farads of super capacitors is it better? Not necessarily. The amount of capacitance (Farads) is only one factor and may not be a real good one when trying to compare one power backup to another. There are other important features to consider besides capacitance. For example a one Farad device can be a lot better than a two farad device. The two farad device may allow lights to run longer but not be able to power a moving train well. There is simply a lot more to it then simply comparing how much capacitance a backup device has built into it. Made In USA
£26.00£23.40
SoundTraxx SoundTraxx 810134 | Golden White LEDs (6 Pack) | Multi Scale
Golden White LED for adding Hyperlight effects or as bulb replacements. 3mm (0.012") diameter 3.3 Volt
£9.72
SoundTraxx SoundTraxx 810121 | 25 x 14mm Speaker Gasket Kit
Package of four gaskets for mounting SoundTraxx 25 x 14mm oval speakers (P.N. STX810112).
£5.04
SoundTraxx SoundTraxx 810141 | Intelligent Consist (IC) Wand For Tsunami SoundCar
For Use With the Tsunami SoundCar Featuring a high-powered magnet, this tool is perfect for waving over SoundCar-equipped models to activate Intelligent Consisting. Measures 5.5” long.
£7.12
SoundTraxx SoundTraxx 810163 | JST-N18 Adapter | N Scale
This adapter allows you to use our smallest decoder (The TSU-N18) in practically any n-scale model! Bring the TSU-N18's 6 functions plus a narrower profile to your models. The JST-Next18 Adapter features a Next18 socket to simply plug-in your TSU-N18 decoder and solder pads for additional functionality. Dimensions: 16 x 9.5 x 5mm. P.N. 810163. Dimensions: 16 x 9.5 x 5mm Function Outputs: 6 Max Function Current: 100mA (ea. Output) Compatible with: SoundTraxx 884010 | Tsunami2 TSU-N18 Steam-2 Digital Sound Decoder SoundTraxx 885026 | Tsunami2 TSU-N18 EMD Diesel Digital Sound Decoder SoundTraxx 885027 | Tsunami2 TSU-N18 GE Diesel Digital Sound Decoder SoundTraxx 885028 | Tsunami2 TSU-N18 ALCO Diesel Digital Sound Decoder SoundTraxx 885029 | Tsunami2 TSU-N18 Baldwin & Other Diesel Digital Sound Decoder SoundTraxx 885030 | Tsunami2 TSU-N18 EMD-2 Diesel Digital Sound Decoder SoundTraxx 886007 | Tsunami2 TSU-N18 Electric Digital Sound Decoder
£11.67
SoundTraxx SoundTraxx 810108 | 15mm Baffle Kit
This snap-together baffle kit is designed for use with our 15mm round speakers (P.N. 810089).
£5.17
SoundTraxx SoundTraxx 810118 | 20mm Speaker Gasket Kit
Package of four gaskets for mounting our 20mm round speakers (P.N. 810053).
£5.04
Digitrax Digitrax SDCK | Signal Driver Cable Kit | Multi Scale
The Digitrax SE74 Signal Decoder is a must-have for any model train enthusiast. With its multi-scale compatibility and precise control, you can easily customize and automate your train signals. Benefit from the professional and objective tone of this product, which relies on domain expertise and scientific language to deliver top-notch performance. Fully connectorized installation. Optional support for DCC 9-Aspect control mode, including Lunars. Easy setup with Option Switches and LocoNet programming. Configurable for four solenoid or four slow-motion turnout control. 8 Input lines for local control and sensors. 8 System routes with 8 entries each. Advanced LocoNet configuration capability with Series7 style installation support using a DT602. More Information Item # SDCK Brand Digitrax MSRP $22.00 TCA Grading C-10 Mint - Brand New Availability In-Stock/Restockable Manuals Instruction Sheet / Specification Sheet
£14.30
