Outhouses by Squeaky's Trains. 2 Pack (1 with door open, 1 with door closed) Exclusive Design by Squeaky's Trains. 3D printed with high quality materials. HO Scale Size (1:87) Hand painted, each outhouse is unique. Unpainted also available.

Read more less

The AM-1 is a module that you can install on your model train layout and control 4 turnouts (switch tracks). The AM-1 can be controlled and setup by a Ring Engineering RailPro Controller, such as the HC-2 Handheld Controller. The AM-1 can also be used to control Accessory Projects. You can control a turntable, swing bridge, oil pumps, lights in buildings, and much more!!! You can use our RailPro Assistant Software to design custom screens for your HC-2 to control your accessories!!! Features: Control up to 4 turnouts per Module Control Snap or Motor Operated Turnouts Size: 4.60 x 3.00 x 1.18 inches     Important Note: When an AM-1 is used as an Accessory Module, the AM-1 hardware has 8 outputs that can be software controlled for 4 motor outputs or 8 sourcing outputs. It also has another 8 I/O that can be configured for 8 inputs or 8 sinking outputs. Currently there is only one software configuration available for the module (2 motor outputs, 4 sinking outputs, and 8 inputs). We expect to offer more software configurations in the future.  

Read more less

By default, this decoder does not come with a pre-programmed Sound Profile. Nevertheless, we provide complimentary Sound File programming for all ESU decoders. Please be aware that opting for Sound File Programming in your order might result in a shipment delay of 1 to 2 business days. Visit this link to preview ESU Sounds With its unique design LokSound 5 DCC Direct, with integrated PowerPack can easily replace boards that provide poor motor control, low volume, or generally inferior sound. Not only will the decoder work fine with most factory installed speakers, but it will sound even better with our new 11x15mm “sugar cube” speaker and sound enclosure kits. Worried about dead spots or pesky yard ladder switches? There’s no need as we’ve built in ESU PowerPack direct into the decoder! Modes The LokSound 5 DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. With its size of 0.67x2.72 inch / 17x69 mm the LokSound 5 DCC Direct, with integrated PowerPack will fit in almost all of the popular North American and Australian H0 manufacturers locomotives. In the DCC format, 14 to 128 speed steps are as natural as 2- and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on fully automatically to a suitable digital central unit. It masters all DCC programming modes and, thanks to RailCom®, the CV values on the main track can be read out with suitable control panels. For panels that can only program the CVs from 1-255, there are auxiliary registers. Braking with DCC brake modules or DC voltage is also possible. An automatic ABC shuttle allows automatic commuting between two stations. The LokSound 5 DCC Direct, with integrated PowerPack decoder can also be used on analog DC tracks. Sound The LokSound 5 DCC Direct, with integrated PowerPack can play up to 10 channels simultaneously. Each channel can be resolved with up to 16 bit / 31250 kHz and finally offers hi-fi quality on your system. There is virtually no difference to the original more audible. A Class D audio power amplifier with up to 3W output powers the speakers, which may have between 4 ohms and 32 ohms impedance. The huge 128 Mbit sound storage provides enough capacity. All individual sounds can be individually adjusted in volume. The super flexible Sound engine without rigid schedule allows the prototypical simulation of all imaginable locomotives. Three separately adjustable braking functions and two alternative load scenarios give you the maximum control over your Locos. Features We know that you want your locomotives to be as realistic as possible. That’s why we packed the LokSound 5 DCC Direct, with integrated PowerPack with function outputs. Depending on the interface version, the LokSound 5 DCC Direct with integrated PowerPack decoder offers at 10 amplified function outputs. Of course tons of lighting effects are also available. The brightness of each output can be set separately. In order to keep compatible with the thousands of LokSound Selects and LokSound V4 decoders already on the market we made sure to add many of the most popular features of that Generation! This Includes the Full Throttle features, including the Famous Drive Hold! Motor Control The engine control of the LokSound 5 DCC Direct, with integrated PowerPack has again been fundamentally improved. A variably adjustable PWM clock frequency of 10kHz to 50kHz ensures especially in bell armature motors for a super quiet operation - The typical “humming” is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique “Auto tune” function allows the automatic decompression of the decoder to the motor. The LokSound 5 DCC Direct, with integrated PowerPack decoder delivers up to 0.75A motor current enough juice for older engines. Energy Storage The LokSound 5 DCC Direct, with integrated PowerPack reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders. With its energy storage (1 Farad capacity) the unit supplies power to all light and motor functions as well as to the sound module. Subject to the energy consumption of your model it may continue to move for up to three seconds. The on board PowerPack incorporates an integral charging circuit controlled by the decoder. Because of this there are no limitations or need to disconnect it during programming like some non-ESU "keep-alive" devices. In order to avoid an undue load on the booster in case there are several models in the same booster sector, the charging current is limited. More Information Item # 58921 Brand ESU Scale HO WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

Here's a great trackside industry for your contemporary HO railroad! The Cornerstone Chocolate Factory is typical of regional specialty producers supplying chocolate to other food producers. A super value with three detailed structure kits and accessories, check out these additional features: Separate two-story brick office Large main building w/truck pull-in and loading dock Railcar and truck receiving building Gravity-feed upright storage tanks Pipe bridge w/piping Unloading/loading rack for tank cars, hoppers and semi-trailers Roof-top vents and three large air conditioners, electrical equipment box and meters, truck docks with weather bellows, roadside sign Easily adapted to other modern industries w/road and rail access Molded in 4 colors with clear acetate Measures Main Building: 20-13/16 x 9-3/8 x 6-3/16" 53 x 23.7 x 15.6cm Receiving Building: 8-7/8 x 5-15/16 x 4-1/2" 22.4 x 15.1 x 11.6 Storage Tanks: 4-7/16 x 2-3/16 x 7-1/2" 11.2 x 5.54 x 19cm Office: 5-29/32 x 3-1/2 x 2-15/16" 15 x 9 x 7.4cm

Read more less

Brand: JT's Mega Steam Scent: Nada (unscented) Size: 2 Oz Glass Bottle with Eye Dropper Made in the USA

Read more less

The LM-3 is a module that you can install into a model train locomotive so the locomotive can be controlled and setup by a Ring Engineering RailPro Controller, such as the HC-2 Handheld Controller with a Color Touch Screen! After the LM-3 is installed in a locomotive, you will be able to control the locomotive speed, direction, up to 6 light outputs! The LM-3 has “Direct Radio” (RF transceiver) built inside. The built in RF module allows commands and data to be sent and received to and from the module. You can load a picture of your choice into the LM-3 module. Then you will be able to touch the screen of the HC-2 to take control of your locomotive!The LM-3 is electrically compatible with the DCC plug found in many locomotives to promote easy installation. Product Specifications: Sound Profile: Universal (all) Dimensions: 1.50 x 0.68 x 0.25 in DCC Track Voltage: 7.5V – 18V Light Outputs 6   The LM-3 is equipped with Direct Radio! This allows Ring Engineering Controlling Devices such as the HC-2, Handheld Controller with Color Touch screen, to control and configure your locomotive by sending and receiving data directly to the LM-3 through the air by use of RF transmission! The Direct Radio is very fast giving your locomotive quick response to your controls. Further, a controlling device can detect your LM-3 with just a few touches on the screen. Because of Direct Radio, you can load a picture of your locomotive to the LM-3! You can also load Light Effects and much more!Radio Load Sharing is a truly an innovative invention from Ring Engineering. It allows your locomotives that are linked together (sometimes called Consisted or MU'ed) to actually share pulling power. Only RailPro equipped locomotives use Direct Radio to talk to each other to be sure each locomotive pulls its share of the load! Even more amazingly, Ring Engineering's patent pending process only takes seconds to setup!Six light outputs. Can be configured for multiple light effects on a single output including On/Off, Dim, Ditch, Mars, Strobe, and more! Additional light effects can be loaded using DirectRadio!Built in protection with fault reporting by Direct Radio!Tiny size 1.50 x 0.68 x 0.25 Inches for easy fit.

Read more less

CD-Quality Sound: TCS’ world-renowned CD-quality sound. 16 Bits of resolution at 44.1kHz sample rate. Back EMF Load Compensation: Provides superior slow speed control and high performance under load. Quiet Drive: Super-quiet motor control for “buzz” free motor performance. Variable Momentum: Allows you to make custom acceleration and deceleration curves. Incandescent Bulb Support: This decoder can be used with 12 Volt bulbs. Function Remapping: Buttons 0 through 12 may be used to control the lighting functions of this decoder. Programmable Lighting Effects: Choose from 20 separate user-programmable lighting effects! Dimmable Brightness: Configure multiple different brightness levels for your LED’s or incandescent bulbs. Decoder Lock: Feature which prevents accidental/unwanted programming while activated. Airwire™ Compatible: Fully compatible with Airwire™ operation. Audio Assist®: TCS exclusive auditory feedback programming system. Program your decoder without the need to memorize CV’s! User-Loadable Speed Tables: Configure custom speed curves and set speed limits. Throttle Modes: Choose from multiple throttle modes to meet your operating needs. Proto Notch™: A WOWSound original feature which uses TCS’ exclusive auto-adjusting BEMF technology to automatically choose the active notch sound. Prototype Mode also offers dynamic sound volumes which accurately model the real-life equivalent. Also includes pre-programmed acceleration and deceleration values. Specs Interface Type: Direct-Plug (21-Pin MTC) Dimensions (L x W x H): 1.28″ x 0.689″ x 0.22″ or 32.5mm x 17.5mm x 5.6mm Scale: HO Scale Continuous/Peak: 1.3/2.0 Amp Total Functions: 8 Function Rating: 100 mA 12V Outputs: 8 Speaker Selection This decoder is optimized for 8 Ω speakers (not included). This decoder uses and audio amplifier capable of supplying up to 2 Watts of power. A 1 Watt minimum power rating is recommended for use with this decoder. If you are using a speaker with less than 1 Watt power rating, you must reduce your volume to prevent speaker failure or amplifier stress. Speaker enclosures greatly increase speaker performance in most cases.

Read more less

This 25mm x 14mm speaker is a tough little beast capable of accepting 2W of audio and still producing a clear and accurate sound. The military spec. rating of these speakers means they are dust proof and IPX5 certified water proof. Truly an impressive speaker in a package small enough for most steam installs and the more dedicated diesel installs. Dimensions: 0.98″ x 0.55″ x 0.3″ or 25mm x 14mm x 7.5mm Sound Pressure Level: 81 dB ± 3.0 dB at 1W, .5m, 1.5 KHz. Effective Frequency Band: 400 Hz. to 20,000 Hz. Power Rating: 2W (Typical) 2.5W (Peak) DC Impedance: 8 Ω ± 15 % at 1.0V 900 Hz.

Read more less

Upgrade your model trains with the Digitrax SDXH167D series 7 sound decoder for HO Scale. Expertly designed with advanced technology, this decoder delivers clear and realistic sound effects for an immersive experience. Enjoy precise control and enhanced functionality with this top-notch decoder. 8 CV-Selectable Steam & Diesel Sound Schemes Included Mobile Decoder with SoundFX v3 Fits many HO locomotives Digitrax 9-Pin Harness Motor 1.0 Amp/2 Amps Peak 6 FX3 Functions, 200ma Output New sound .spjs loadable with Digitrax USB programmer 10-Pin sound harness with 8 Ohm 16 x 26 x 9mm Box Speaker 300uF Capacitor More Information Item # SDXH167D Brand Digitrax Scale HO Scale MSRP $59.00 TCA Grading C-10 Mint - Brand New Availability In-Stock/Restockable Manuals Instruction Sheet

Read more less

The ESU Premium Foam Train Service Tray is the ideal tool for the maintenance and care of your locomotives. Two recesses are available for perfect work: The locomotive can be clamped upside down to comfortably reach the underbody of the locomotive. In the classic inclined tray, you can easily reach the sidewalls of the locomotive or set up the locomotive almost vertically, in order to achieve the interior of the locomotive well. The Premium Foam Train Service Tray consists of a soft, fine-pored foam with high restoring force. As a result, small parts such as handle bars, antennas or pantographs cannot get caught and thus reduce the possibility of damage to a minimum. The material is resistant to oil, grease and other cleaning agents. For safe storage of small parts and screws, a magnetic storage recess is available over the entire length. The Premium Foam Train Service Tray is 328mm long and can be arranged in rows, so that longer Service Trays for the maintenance of railcars can be built. WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

Since smart phones with touch screens have almost completely replaced the conventional mobile phone, model train enthusiasts and manufacturers face the question how to employ more powerful devices for controlling model trains. As a result of this, many apps have been developed lately, which can be uploaded onto your mobile phone and used for running your trains. This concept, however, has one disadvantage, namely that smart phones have not been primarily designed for running model trains. Due to the lack of suitable input elements the operator is forced to spend most of the time looking at the display. The limits become quickly obvious so we at ESU had a look at the question on how to utilize the advantages of the smart phone technology and combine it with the needs of model train enthusiasts. It is with great joy that we now present the results of our considerations. With the new ESU CabControl DCC system you have wireless control of your locomotives, accessories and routes simply by Wi-Fi! With the 50310 CabControl Integrated Control Unit, advanced model railroading is as simple as ever. With our new system, you have full control over your locomotives, switches and signals just at the tap of a finger. The unit communicates with our Mobile Control II Wireless Controller via wireless LAN. The CabControl’s integrated 7 Amp booster also allows it to power even larger layouts with ease. LokSound decoders equipped with RailComPlus® even register automatically with the system! Running trains has finally caught up with the technology of today! CabControl - Integrated Control Unit ESU’s “North American” System This system was specially developed for use in North America and Australia. American and Australian locomotive icons (along with European Icons) Easy Consisting for multiple unit lash-ups using drop down menus Wireless walk around system making it easy to follow your train on a large layout. Technical Specification CabControl Features All DCC modes (14, 28, 128 speed steps) Long and short addresses Over 16,000 locomotives can be arranged and controlled Up to 28 functions per locomotive All Scales can be used with the CabControl system with the variable voltage 7Amp Power Supply Built-in WLAN Access Point Creates a unique Wifi-Network for your Mobile Control II Wireless throttles Supports at least 32 Mobile Control II Wireless ControllersCompliant with all relevant IEEE WLAN standards. Suitable for use in America and Europe The CabControl features a LAN port to connect the box to your home network. Via the home network, the CabControl can be connected to Model RailRoad Control Software. “ECoSlink” port For easy connection with our ESU boosters, CabControl supports ECoSlink, a high speed, CAN based bus system. The CabControl built-in booster has so much power that, in most cases, you don‘t need additional ones. Hook Up Hook up is simple with the CabControl system. All you have to do is plug the 7 Amp power supply into the CabControl box and then hook up your CabControl box to your track for track power and its ready to go!  The wireless controllers automatically connect to the system via WLAN.  Upgradable On occasion new features will be added to the CabControl system. Gone are the days of having to send your DCC command station back to the manufacturer for updates! When a new update becomes available it is as simple as loading this to a USB Data stick and plugging it in to the back of the system. Easy! Protection Each CabControl system meets the relevant requirements regarding safety and operation on a layout: The track outlet is protected against overload as well as short circuits. Each CabControl system can differentiate between a “genuine” short, and a momentary current drain when passing over switches or gaps. We place value on the indestructibility of the device, just like we do with our mobile decoders. Expansion As the CabControl System uses the ESU Mobile Control II Wireless Throttles, expansion is easy as these throttles are already available and will connect automatically to the Integrated Control Unit. The system can also be used with the ECoSBoost Boosters using the ECoSlink Terminals when more power is needed for large layouts. CabControl - Handheld Wireless Throttle Ergonomics & Functionality Combined When you hold your CabControl Throttle in your hands for the first time you will immediately notice its excellent ergonomics. All Parts of the screen can easily be reached with one hand, and unlike a cell phone throttle, the most important functions can even be reached “without looking” giving you the ability to watch your trains and not needing to watch your throttle. This is due to the central, motorized throttle knob with end stop. With this knob you can delicately control the speed of your trains and change direction. For activating functions simply touch the icons on the display. The display also serves for changing functions – exactly the same way as you know it from your mobile phone.  Finally, two buttons each on either side serve for changing direction or triggering the most important functions. These side buttons are user editable giving you the choice of what you want to control with them. Colorized Function Icons are displayed showing what function does what. Gone are the days of having to memorize what function button control what decoder feature. Running Locomotives The CabControl Throttles can control all locomotives registered in the system and supports 14, 28 or 128 speed steps. All of the important locomotive properties such as name, a picture, function mapping as well as easily identifiable icons for function buttons will be taken from the Integrated Control Unit and will be displayed correctly. You may switch up to 28 functions for each locomotive, which, of course, can either be momentary or continuous functions. You read that correctly! EVERY Function Button can be momentary or latching depending on your use! No more limitations on how you function map your decoders. As standards are constantly changing and the number of DCC function buttons is increased a simple update will allow for even more! Controlling Accessories The CabControl System has the ability to run over 1000 magnetic accessories. More Fun in Operations The high resolution (480 x 800 pixels, 280 dpi), backlit TFT display of the CabControl Throttle always keeps you up to date on the most important operating parameters. Furthermore, you can see if another operator controls a certain locomotive or if an emergency stop has been triggered. The permanently installed, powerful Lithium polymer rechargeable battery will serve you right through the most extensive operating sessions giving 5-8 hours of operation based on how you are using your throttles. Recharge the batteries of your CabControl simply by using the USB port on the Integrated Control Unit and the supplied Micro USB Cable or the battery charger of your mobile phone or any other USB port. Open Platform The CabControl Throttles are based on the Android operating system. We have created a powerful basis for this open, globally used operating system:  The ARM® Cortex® A8 microprocessor clocked with 1.3 GHz and controls a high resolution 3.2 inch TFT color display. A capacitive touch screen assures touch-free data entry. For communicating with the “outside world” there is an USB port and a WLAN interface. Thanks to the standardized radio control interface, trouble free operation of your layout can be assured at any time. The range can be extended with WLAN repeaters, if necessary. Due to the open platform design you may add further apps for the Google Play Store at any time.   *The CabControl DCC System was specifically created for the North American and Australian Market and as such can only be purchased though ESU LLC in the USA. More Information Item # 50310 Brand ESU Scale Multi

Read more less