Under $10

Gray Insulating Fiber Washers .010in Thick Gray insulated fiber washer. 1/4"OD x 1/8" ID x .010" thick. Made form vulcanized fiber with a UL 94 HB rating. Useful as spacers for adjusting car height and in many other applications. 4 dozen per package.

Read more less

#322 Between-the-Rails Code 83 Delayed-Action Magnetic Uncoupler - HO Scale Place this handy "delayed-action" Uncoupler anywhere on a straight track segment between-the-rails. Ready to mount on top of ties with Code 83 rail. Cut out ties if mounting Code 70, 55 or 40 rail. Track not included Use the #334 Uncoupler Gluing Jig to aid in the precision installation of #312, #321 & #322 Uncouplers in track. Package Includes: (1) each #322 Between-the-Rails Code 83 Delayed-Action Magnetic Uncoupler

Read more less

#533 - 33" Diameter Ribbed Back Wheelsets (Code 88) - HO Scale Ribbed wheelsets are most commonly found on steam era rolling stock. Kadee® wheel sets are manufactured to the most exacting standards and feature: RP-25 contour, non-magnetic metal wheels and insulated needlepoint axles. Twelve Sets (1 Set = 1 Axle) Axle Tip to Tip: 1.018" Wheelset Features: Code 88 (.088") 33" Ribbed Back Wheels Accurate markings Incredible detail true to prototype Non-magnetic Metal Wheels Smooth tracking Free rolling Contoured Insulated Axles RP-25 Free rolling wheels Needlepoint Axles Axle Tip to Tip: 1.018" Freight & Passenger Package Includes: (12) Sets #533 33" Diameter Ribbed Back Wheelsets (Code 88)   The term Code 110 and Code 88 relates to the width of the wheels and has no relationship to track code. Code 110 wheels are .110" wide and Code 88 are .088" wide. Code 110 wheels are the common (or "Standard") width wheels and Code 88 are what is called "Semi-Scale" and are used when the modeler wants a more prototypical looking wheel width. Actual HO-Scale prototypical wheel width would be around .067" wide and although they will run OK on the average track they will not go through common turnouts and crossings. Code 88 (.088") is just about the minimum width of wheel that will run on most standard or common track if gauged correctly. It really is a matter of appearances because there's very little operational differences between running Code 110 or Code 88 wheels. Code 88 wheels look really good and are most noticeable on open frame cars like hoppers and tank cars. However, they also look great on boxcars, gondolas, and reefers but not quite as noticeable. As mentioned above track code and wheel code have no relationship meaning Code 110 and Code 88 will run on most any code of track. Track code is simply the measured height of the rail, code 100 is .100" tall, code 83 is .083" tall, code 70 is .070" tall, and so on.

Read more less

#242 HO Scale Universal "Black Box" Snap-Together Insulated Gearbox & Lids Precision engineered to work with Kadee® NO.5®, 58, 20-Series and 40-Series & All Whisker® Couplers. 10 pair per package 2-56 screws are the most commonly used for center hole.Screw length will very depending on the mounting situation.

Read more less

This industry leading coupler features an all metal coupler head, shank, and Whisker® centering spring and comes complete with insulated draft gearbox and lid. The #142 Magne-Matic® Whisker® Metal Coupler may be mounted with the included #242 Snap-Together Gearbox or with other manufacturers cast-on coupler pockets. It is not recommended to use a metal coupler directly on a metal surface or in a metal draft gearbox to avoid possible electrical crossover and shorting that may cause damage. Use the provided insulated gearbox or insulated #22 coupler. HO-Scale Package Includes: (2) Pair #142 Whisker® Metal Couplers - Medium Overset Shank (2) Pair #242 Snap-Together Gearboxes (2) #622 Knuckle Springs #142 Whisker® Metal Coupler Features: Material  -   Metal Shank Length  -  Medium(9/32") (center hole to back of coupler head) Coupler Offset  -   Overset Knuckle Spring  -   #622 Centering System  -   Whisker® Head  -   Standard Head Works In Place of  -   #22, #32 (#142 in a #252 box), Medium Overset "clone" couplers Works With  -   #213, #232, #234, #242, #252, #262, manufacturer cast-on draft gearboxes #242 Snap-Together Gearbox Features: Material  -   Insulated Plastic Lid Type  -   Snap-Together Dimensions  -   7/16"L x 5/16"W x 1/8"H Works With  -   NO.5®, #58, 20-Series and 40-Series, All Whisker® Couplers Mounting Specifications: Mounting Height  -   1/2" Centerline  -   25/64" Trip Pin Height  -   1/32" Center Hole  -   2-56 Insulated Screws are the most commonly used. (Screw length will vary) Recommended Tools: #206 Insulated Muti-Purpose Coupler Height Gauge #231 Greas-em Dry Graphite Lubricant #237 Coupler Trip Pin Pliers #240 Double Headed Pin Vise #241 Dual Tool Manual Uncoupling Tool and Spring Pick #246 Tap (2-56) and Drills (#50 and #43)

Read more less

This snap-together baffle kit is designed for use with our 20mm round speakers (P.N. 810053).

Read more less

Sunny White LED for adding Hyperlight effects or as bulb replacements. 3mm (0.012") diameter 3.3 Volt

Read more less

The TSU-4400 is designed for models with higher stall currents such as some S, O, and large scale locomotives; this decoder features easy-to-use terminal blocks for no-fault wiring and a higher audio amplifier for awesome volume, indoors or out. You will feel like you are in the cab with the amazing new features that Tsunami2 has to offer including: Reactive Dynamic Digital Exhaust, Functioning locomotive and train brakes, injectors, power reverse, and firebox flicker. We also offer a large selection of selectable sound effects including: exhaust chuffs(10), prime movers (up to 12), bells (12), Whistles (90), airhorns (40+), couplers, dynamos and more! This 4-amp, universal-style format decoder includes a connector to easily add a CurrentKeeper (P.N. STX810140) to maintain performance over dirty track and switches. Product Specifications: Sound Profile: ALCO Diesel Dimensions: 69 x 30.5 x 14mm Max. Motor Stall Current: 4A Max. Function Current: 400mA (each output) Function Outputs: 6 Audio Amplifier: 3 Watt, 8-Ohm Load DCC Track Voltage: 7.5V – 26V Sound Channels: 16

Read more less

The TSU-21PNEM8 is a 1-amp Digital Sound Decoder with 8 function outputs. It is designed for easy plug-in operation when mated to a 21-pin NEM connector. You will feel like you are in the cab with the amazing new features that Tsunami2 has to offer including: Reactive Dynamic Digital Exhaust, Functioning locomotive and train brakes, injectors, power reverse, and firebox flicker. They also offer a large selection of selectable sound effects including: exhaust chuffs(10), prime movers (up to 12), bells (12), Whistles (90), airhorns (40+), couplers, dynamos and more! The TSU-21PNEM8 can be wired to a CurrentKeeper (P.N. 810140) to maintain performance over dirty track and switches. Product Specifications: Sound Profile: EMD-2 Dimensions: 30.5 x 15.5 x 6.5mm Max. Motor Stall Current: 1A Max. Function Current: 100mA (each output) Function Outputs: 8 Audio Amplifier: 2 Watt, 8-Ohm Load DCC Track Voltage: 7.5V – 22V Sound Channels: 16

Read more less

The new ESU PowerPack Mini can be wired to all fourth and fifth generation ESU decoders. It reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders. With its energy storage (1 Farad capacity) the unit supplies power to all light and motor functions as well as to the sound module. Subject to the energy consumption of your model it may continue to move for up to three seconds. The PowerPack Mini incorporates an integral charging circuit controlled by the decoder. Therefore it may be connected even during programming. In order to avoid an undue load on the booster in case there are several models in the same booster sector, the charging current is limited. The buffer time can be reduced by means of a CV. This may be useful to assure the correct stopping position ahead of signals showing the “Stop” aspect (red signal). Although it is considerably smaller than its predecessor, the space requirements of the PowerPack Mini of about 15.7 mm x 9.7 mm x 13 mm must be taken into account when installing this unit. A three-pole wire harness connects the PowerPack Mini to the decoder. The wires are already soldered to the PowerPack Mini and must be soldered to the appropriate solder pads of the decoder. More Information Item # 54671 Brand ESU Scale Multi WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

You want to listen to the sound spectrum of your favourite loco, or the special sound of that loco around the corner in the yard – on your model railroad? No problem with ESU’s LokProgrammer! One prerequisite: A PC with sound card and Windows (Windows 8.1 and higher). Simply record the original sound of your engine and edit it at home with your computer. Many customers did this already successfully. Even if you don’t yet belong to this elite group of LokSound Pro’s, the LokProgrammer is still a very useful tool for you. It is the easiest way to program your ESU-decoder. You need no programming experience, thanks to the graphic screen everything falls into place with a few mouse clicks. What the LokProgrammer can do: Change the sound safed on the decoder. Setting of all digital parameters of the Loksound decoder such as address of the loco, operation speed, maximum speed, braking deceleration, brightness of bulbs etc; you can set all options with your computer very easily - no cumbersome entering of CVs (configuration variables) with your command station. Rearrange your sounds and transfer it to the LokSound decoder. You can use all sounds that can be downloaded to your computer hard disk. Sound can be allocated to different events. Additional sounds can be activated via function buttons. Sound With the LokProgrammer you can erase the sound data of any LokSound decoder as many times as you wish, and replace it with a different sound. To this end we offer on our homepage more than 200 different, fully matching sounds of various prototypes and locos for downloading on your computer. Also you can edit just parts of a sound project: You don’t like the decoder’swhistle? Just replace it with one of the many others. Suitable sources beside those offered by us, are in Windows *.wav format available. Sound – even voice or music is no problem for our decoders. With the LokProgrammer’s aid you use the entire flexibility and functionality offered by LokSound decoders. Programming By the same token, all other ESU decoders profit from the LokProgrammer’s versatility; no matter if DCC, Multiprotocol - or mfx decoder. With its help it’s possible to edit all parameters of the particular decoder simply and conveniently. The available options depend on the kind of decoder. Beside addresses and acceleration - and deceleration settings, this concerns above all the allotment of function keys (function mapping), the allocation of special effects to the individual outputs, or the lamp brightness. The LokProgrammer can also help when optimizing back EMF parameters or the loadable speed table. All options can be programmed very conveniently: There is no tedious punching-in of CV-numbers at the digital station anymore. Hook up It’s this simple: The LokProgrammer is a small programming box, which is wired between the PC and a programming track. To connect it you need either a vacant serial interface, or you use the included USBadapter cable (works with Windows up to Windwos 10). For power we include a 500 mA wall power supply. If your needs are greater (e.g. for gauge I engines), you can also use a conventional model railroad transformer. Software After hook-up you start up the especially user-friendly LokProgrammer software. This runs on all modern Windows-systems (Windows 8.1 and higher). Just put the loco with the ESU decoder on your programming track, and right away you can read, edit or program it. The Programmer automatically recognizes the decoder in the engine. Simplicity The LokProgrammer is recommended not only for the use with our ESU decoders: By now, many well known model railroad manufacturers factory-furnish their locos with ESU-decoders, which of course can be modified again within the frame work of their technical specifications – with the help of the LokProgrammer. You see, purchasing a LokProgrammer pays off in any case. Upgrades The LokProgrammer can also be instrumental in updating decoders. Almost all ESU decoders are updatable, in case you desire a new software version. To do this, you only need the LokProgrammer and a small update-program, which you can download from our homepage. The future LokProgrammer software is being reviewed continuously. The latest, pertinent version can always be downloaded from our homepage, or can be installed automatically, through an internet-update function, on your computer. More Information Item # 53452 Brand ESU Scale Multi

Read more less

This iMax B6AC is a rapid charger with a high-performance microprocessor. Features: Microprocessor controlled Delta-peak sensitivity. Individual cell balancing Li-ion, LiPo and LiFe capable Ni-Cd and NiMH capable Large range of charge currents Store function, allows safe storage current Time limit function Input voltage monitoring. (Protects car batteries at the field) Data storage (Store up to 5 packs in memory) Battery break in and cycling. Support new generation 123 system (LiFe) battery   Specifications: Operating voltage range: DC11.0-18.0 Volt / AC to DC adaptor(DC11.0-18.0V/5A) Circuit power:  Max.charge power 80W    /     Max.discharge power 5W Charge Current Range: .1~5.0A Discharge current range: 0.1-1.0A Current drain for balancing Li-po: 300mAH/cell LiIon/LiPo/LiFe cells : 1-6 NiCd/NiMH cells : 1-15 Pb battery voltage: 2~20v Unit Package Gross Weight: 580g Dimensions: 133x87x33mm Compare to iMAX B5: Can charge 6 cells LiPo battery (B5 can charge maximum 5 cells) With Discharge Function 123 Life Charging Package: 1 x IMAX B6 AC 80W 1 x Power adapter (US plug) 1 x Charging Cable  

Read more less