$25 to $50
Woodland Scenics Woodland Scenics 93 | Lump Coal | Multi Scale
Use this natural, realistic product to model coal loads and piles. Use for any scale and apply with Scenic Cement™. Model coal loads and piles Natural, realistic product For any scale 10.8 in3 (176 cm3)
$4.59
SoundTraxx SoundTraxx 810132 | Locomotive-to-Tender Wiring Kit (DBX-9000)
The SoundTraxx Locomotive-to-Tender Wiring Kit (DBX-9000) is a quick-disconnect wiring harness assembly for separating the locomotive from the tender.
$15.96
Ring Engineering Ring Engineering LM-3S | RailPro HO Scale Locomotive Module with Sound
The LM-3S is a module that you can install into a model train locomotive so the locomotive can be controlled and setup by a Ring Engineering RailPro Controller, such as the HC-2 Handheld Controller with a Color Touch Screen! After the LM-3S is installed in a locomotive, you will be able to control the locomotive speed, direction, up to 6 light outputs and sounds! The LM-3S has “Direct Radio” (RF transceiver) built inside. The built in RF module allows commands and data to be sent and received to and from the module. You can load a picture of your choice into the LM-3S module. Then you will be able to touch the screen of the HC-2 to take control of your locomotive! You can even download new sounds and light effects using the built in Direct Radio!The LM-3S is electrically compatible with the DCC plug found in many locomotives to promote easy installation. Product Specifications: Sound Profile: Universal (all) Dimensions: 1.50 x 0.68 x 0.25 in DCC Track Voltage: 7.5V – 18V Light Outputs 6 The LM-3 is equipped with Direct Radio! This allows Ring Engineering Controlling Devices such as the HC-2, Handheld Controller with Color Touch screen, to control and configure your locomotive by sending and receiving data directly to the LM-3 through the air by use of RF transmission! The Direct Radio is very fast giving your locomotive quick response to your controls. Further, a controlling device can detect your LM-3 with just a few touches on the screen. Because of Direct Radio, you can load a picture of your locomotive to the LM-3! You can also load Light Effects and much more!Radio Load Sharing is a truly an innovative invention from Ring Engineering. It allows your locomotives that are linked together (sometimes called Consisted or MU'ed) to actually share pulling power. Only RailPro equipped locomotives use Direct Radio to talk to each other to be sure each locomotive pulls its share of the load! Even more amazingly, Ring Engineering's patent pending process only takes seconds to setup!Six light outputs. Can be configured for multiple light effects on a single output including On/Off, Dim, Ditch, Mars, Strobe, and more! Additional light effects can be loaded using DirectRadio!Built in protection with fault reporting by Direct Radio!Tiny size 1.50 x 0.68 x 0.25 Inches for easy fit.
$79.99
SoundTraxx SoundTraxx 810158 | CurrentKeeper 2-Pin Wiring Harness
Easily connect a CurrentKeeper or extra capacitor to any SoundTraxx decoder equipped with a 2-pin “Quick Plug” to improve performance over dirty track and switches.
$7.16
NCE NCE 25 | DCC Power Cab Starter System - 2amp with Power Supply | Multi Scale
An entire DCC system in the palm of your hand! The Power Cab system can operate one or two HO locomotives. The Power Cab provides all of the capability and ease of use that you’ve heard about in the NCE Power Pro system, at an entry level price.Installation is a snap. Hook two wires to your track and plug in the cab. You’re off and running trains!The Power Cab kit contains: Power Cab 7' Power Cab Cable PCP Power Panel Power Supply Pro Cab Coiled Cord Manual. More Information Item # 0025 Scale Multi Scale
$194.95
NixTrainz NixTrainz | Decoder Buddy Mini (2.2k Ohm Resistors Onboard)
The Decoder Buddy Mini was developed to fit into smaller steam and diesel applications. there has also been interest in HOn3 and S-Gauge applications. This mother board does not include the 21 Pin Decoder. This mother board requires soldering. These printed circuit board is NOT INTENDED FOR USE IN A DC SYSTEM. The mother board includes: One 21 Pin Decoder receptacle Two pairs of track input pads One pair of motor input pads One set of stay alive pads (U+ , GND and if necessary a third control wire ) One pair of speaker pads Resistors for use with LED lighting. (Also available with 0 ohm, 750 ohm and custom specified resistors for function outputs. This accommodates some previously installed and "12 volt LEDs".) It is IMPORTANT to realize that resistors must be used when LEDs are connected to the four lighting outputs of the Mini!!! The resistors may be soldered in line when purchased or the included resistors may be soldered inline upon installation. Remember there are different incandescent lamp voltage requirements and current draw that have to be taken into consideration also. (Until the next batch is produced the Mini will be labeled Tiny and the picture on the package will indicate the correct headlight outputs for direction of locomotive.)
$10.99$9.89
Woodland Scenics Woodland Scenics 626 | Static Grass Medium Green 12mm | Multi Scale
Static Grass 28 grams Grass length: 12mmm
$4.50$4.05
Woodland Scenics Woodland Scenics 5725 | Just Plug Lighting System - Auxiliary Switch | Multi Scale
Turn lights on and off with the flick of a switch. Control the power to a Light Hub, Sequencing Light Hub, Expansion Hub or to multiple Hubs. Easily mount switch to main control panel with mounting screws or double-sided tape, if desired. Switch face includes labeling space for quick identification. ROHS Compliant
$7.95
Woodland Scenics Woodland Scenics 5755 | Just Plug Lighting System | Red LED Flashing Nano Lights 30mA (2)
Red LED Flashing Nano Lights 30mA Includes 24" cables 2 lights per package Ready to plug into Light Hub (sold separately) INSTRUCTIONS: Align locking tabs on Light Plug with front of Light Hub (JP5700, JP5701) and insert into LIGHT Port until locking tabs click into place. Glue or tape Light in place, as required. Pink plastic band (1/2") on cable identifies Red Flashing light.
$9.79
Woodland Scenics Woodland Scenics 92 | Mine Run Coal | Multi Scale
Use this natural, realistic product to model coal loads and piles. Use for any scale and apply with Scenic Cement™. Model coal loads and piles Natural, realistic product For any scale 10.8 in3 (176 cm3)
$4.59
SoundTraxx SoundTraxx 810090 | 50 x 90mm Oval Speaker | Large Scale
This is one of our largest speakers for use with the TSU-4400 in O-scale or larger models. Dimensions: 50 x 90 x37.5mm(D)Frequency Response: 230Hz - 20kHzPower: 2 Watts (Nominal) 5 Watts (Peak)Impedance: 8 Ohms
$15.16
SoundTraxx SoundTraxx 810129 | 23mm Square Mega Bass Speaker 8-ohm 2 watt
This speaker is perfect for enhancing the low bass sounds that are found in most diesel decoders. It is well worth the extra effort! Dimensions: 23 x 23 x 10.2mm(D)Frequency Response: 275Hz – 20kHzPower: 2 Watts (Nominal) 4 Watts (Peak)Impedance: 8 Ohms
$10.36
