Locomotives
WalthersProto Walthers Proto 920-49560 | EMD FP7 - Standard DC / DCC Ready - Southern Pacific(TM) #6455 | HO Scale
Enjoy complimentary shipping! Bundle your purchases for even more savings with our free shipping option. (This offer is optional) Providing enough steam to power train heat and some air conditioning systems on postwar trains taxed the standard water supply of EMD F7 A units set-up for passenger service, prompting EMD to rollout the new FP7 in 1949. Though outwardly similar to the F7A, FP7s were actually four feet longer to accommodate bigger water tanks with a capacity of 950 US gallons. Standard passenger power into the Amtrak era and beyond (with some also handling freight chores), these WalthersProto replicas are fully assembled and ready for service with: One time run of these roadnumbers, order now - limited quantity available! Matches the prototypes' extended frame and body Available with ESU LokSound 5 Sound & DCC for DCC and DC layouts Railroad-specific details Five-pole, skew-wound, high-torque, high-efficiency can motor Helical gears with 14:1 ratio for smooth, ultra-quiet running Easy multiple-unit operation Correct RP-25 wheels Proto MAX(TM) magnetic metal knuckle couplers Finished in the later gray and red scheme, these HO WalthersProto replicas feature: Nathan M-5 air horn Whip-type radio antenna with conduit SP-style snowplow pilot Upper headlight with twin sealed-beam (operating) and red emergency (UDE) lights (nonworking) Working rear back-up light Frame-mounted equipment box Rooftop photo-etched icicle breakers front and rear More Information Item # 920-49560 Brand WalthersProto Scale HO Engine Electronics DC, DCC Ready Type EMD Diesel Road Name Southern Pacific(TM) Road Number 6455 Estimated Release Date June 2024
£132.65
WalthersProto Walthers Proto 920-42560 | EMD FP7 - ESU® Sound & DCC - Southern Pacific(TM) #6453 | HO Scale
Enjoy complimentary shipping! Bundle your purchases for even more savings with our free shipping option. (This offer is optional) Great for railroads that preferred four-axle diesels for their passenger runs, prototypes for the WalthersProto EMD FP7 came equipped with more boiler water capacity on their stretched chassis. Providing enough steam to power train heat and some air conditioning systems on postwar trains taxed the standard water supply of standard EMD F7 A units set-up for passenger service, prompting EMD to roll out the new FP7 in 1949. Though outwardly similar to the F7A, FP7s were actually four feet longer to accommodate bigger water tanks with a capacity of 950 US gallons. Standard passenger power into the Amtrak era and beyond (with some also handling freight chores), these WalthersProto HO EMD FP7 replicas are fully assembled and ready for service with: One time run of these roadnumbers, order now - limited quantity available! Matches the prototypes' extended frame and body Available with ESU LokSound 5 Sound and DCC for DCC and DC layouts Railroad-specific details Five-pole, skew-wound, high-torque, high-efficiency can motor Helical gears with 14:1 ratio for smooth, ultra-quiet running Easy multiple-unit operation Correct RP-25 wheels Proto MAX(TM) magnetic metal knuckle couplers Finished in the later gray and red scheme, these HO WalthersProto replicas feature: Nathan M-5 air horn Whip-type radio antenna with conduit SP-style snowplow pilot Upper headlight with twin sealed-beam (operating) and red emergency (UDE) lights (nonworking) Working rear back-up light Frame-mounted equipment box Rooftop photo-etched icicle breakers front and rear The F7B features: Working back-up light on both endsLifting lugs on both endsPartial body skirt More Information Item # 920-42560 Brand WalthersProto Scale HO Engine Electronics DC, DCC & Sound Type EMD Diesel Road Name Southern Pacific(TM) Road Number 6453 Estimated Release Date June 2024
£198.99
WalthersProto Walthers Proto 920-49548 | EMD FP7 - Standard DC / DCC Ready - Chesapeake & Ohio #8006 | HO Scale
Enjoy complimentary shipping! Bundle your purchases for even more savings with our free shipping option. (This offer is optional) Providing enough steam to power train heat and some air conditioning systems on postwar trains taxed the standard water supply of EMD F7 A units set-up for passenger service, prompting EMD to roll out the new FP7 in 1949. Though outwardly similar to the F7A, FP7s were actually four feet longer to accommodate bigger water tanks with a capacity of 950 US gallons. Standard passenger power into the Amtrak era and beyond (with some also handling freight chores), these WalthersProto replicas are fully assembled and ready for service with: One time run of these roadnumbers, order now - limited quantity available! Matches the prototypes' extended frame and body Railroad-specific details Five-pole, skew-wound, high-torque, high-efficiency can motor Helical gears with 14:1 ratio for smooth, ultra-quiet running Easy multiple-unit operation Correct RP-25 wheelsets Proto MAX(TM) magnetic metal knuckle couplers Road-specific details of this WalthersProto replica include: A unit details - Nathan M5 Air horn w/all bells forward Whip-style radio antenna w/conduit Freight pilot Knob-style sand hatch doors Late water filler Cab wind deflectors Etched-metal cab sunshades Standard type winterization hatch Vertical body louvers Photo-etched Farr vertical grilles Dual headlights - upper single, lower twin vertical More Information Item # 920-49548 Brand WalthersProto Scale HO Engine Electronics DC, DCC Ready Type EMD Diesel Road Name Chesapeake & Ohio Road Number 8006 Estimated Release Date June 2024
£132.65£119.39
WalthersProto Walthers Proto 920-42548 | EMD FP7 - ESU® Sound & DCC - Chesapeake & Ohio #8008 | HO Scale
Enjoy complimentary shipping! Bundle your purchases for even more savings with our free shipping option. (This offer is optional) Great for railroads that preferred four-axle diesels for their passenger runs, prototypes for the WalthersProto EMD FP7 came equipped with more boiler water capacity on their stretched chassis. Providing enough steam to power train heat and some air conditioning systems on postwar trains taxed the standard water supply of standard EMD F7 A units set-up for passenger service, prompting EMD to roll out the new FP7 in 1949. Though outwardly similar to the F7A, FP7s were actually four feet longer to accommodate bigger water tanks with a capacity of 950 US gallons. Standard passenger power into the Amtrak era and beyond (with some also handling freight chores), these WalthersProto HO EMD FP7 replicas are fully assembled and ready for service with: One time run of these roadnumbers, order now - limited quantity available! Matches the prototypes' extended frame and body Available with ESU LokSound 5 Sound and DCC for DCC and DC layouts Railroad-specific details Five-pole, skew-wound, high-torque, high-efficiency can motor Helical gears with 14:1 ratio for smooth, ultra-quiet running Easy multiple-unit operation Correct RP-25 wheels Proto MAX(TM) magnetic metal knuckle couplers Road-specific details of this WalthersProto replica include: A unit details - Nathan M5 Air horn w/all bells forward Whip-style radio antenna w/conduit Freight pilot Knob-style sand hatch doors Late water filler Cab wind deflectors Etched-metal cab sunshades Standard type winterization hatch Vertical body louvers Photo-etched Farr vertical grilles Dual headlights - upper single, lower twin vertical More Information Item # 920-42548 Brand WalthersProto Scale HO Engine Electronics DC, DCC & Sound Type EMD Diesel Road Name Chesapeake & Ohio Road Number 8008 Released Date June 2024
£198.99£179.09
WalthersProto Walthers Proto 920-49920 | EMD E8 A-A - Standard DC / DCC Ready - Southern #6902 & 6910 | HO Scale
Power your HO railroad's flagship streamliners with these superb replicas of EMD's famed E8 and E9 diesels. Introduced in 1948 with the new 567B prime mover, production continued until 1954 when the virtually identical E9 was introduced with the more powerful 567C prime mover. Powerful, reliable and economical, EMD E units handled premiere long-distance trains for decades, with many ending their long careers in commuter service and occasionally handling fast freight trains. Fully assembled and ready for service, features include: One time run of these roadnumbers, order now - limited quantity available! Road- and era-specific details Both units powered - matching individual A units available separately Rugged and reliable WalthersProto drive 21-pin DCC plug Formed wire grab irons and handrails Photo-etched lift rings Cab interior w/seats and figures All-wheel drive and electrical pickup Constant and directional LED lights Correct size RP-25 metal wheels Proto MAX(TM) metal knuckle couplersRoad-specific features of this WalthersProto replica include: Nathan five-chime (all forward) air horn Single horizontal sealed-beam headlight Working backup light Flush number boards Removed skirts Freight pilot Southern-style MU bracket 4-hose MU set at left and right Photo-etched E8A-style Farr air grilles Dynamic brake with 48" fan Winterization hatches w/levers Single offset steam generator Rooftop air reservoirs w/piping Round spark arrestors Rectangular air vent Roller bearing sideframes Wheel slip hubs Speed recorder Southern-style left and right water tanks More Information Item # 920-49920 Brand WalthersProto Scale HO Engine Electronics DC / DCC Ready Type EMD Diesel Road Name Southern Road Number 6902 & 6910
£265.32£238.79
WalthersProto Walthers Proto 920-42920 | EMD E8 A-A - ESU® Sound & DCC - Southern #6902 & 6910 | HO Scale
Power your HO railroad's flagship streamliners with these superb replicas of EMD's famed E8 and E9 diesels. Introduced in 1948 with the new 567B prime mover, production contiued until 1954 when the virtually identical E9 was introduced with the more powerful 567C prime mover. Powerful, reliable and economical, EMD E units handled premiere long-distance trains for decades, with many ending their long careers in commuter service and ocassionally handling fast freight trains. Fully assembled and ready for service, features include: One time run of these roadnumbers, order now - limited quantity available! Available with LokSound 5 for DCC or DC layouts Road- and era-specific details Both units powered - matching individual A units available separately Rugged and reliable WalthersProto drive 21-pin DCC plug Formed wire grab irons and handrails Photo-etched lift rings Cab interior w/seats and figures All-wheel drive and electrical pickup Constant and directional LED lights Correct size RP-25 metal wheels Proto MAX(TM) metal knuckle couplers Road-specific features of this WalthersProto replica include: Nathan five-chime (all forward) air horn Single horizontal sealed-beam headlight Working backup light Flush number boards Removed skirts Freight pilot Southern-style MU bracket 4-hose MU set at left and right Photo-etched E8A-style Farr air grilles Dynamic brake with 48" fan Winterization hatches w/levers Single offset steam generator Rooftop air reservoirs w/piping Round spark arrestors Rectangular air vent Roller bearing sideframes Wheel slip hubs Speed recorder Southern-style left and right water tanks More Information Item # 920-42920 Brand WalthersProto Scale HO Engine Electronics DC, DCC & Sound Type EMD Diesel Road Name Southern Road Number 6902 & 6910
£397.99£358.20
WalthersMainline WalthersMainline 910-19480 | EMD F40PH - ESU® Sound & DCC - Grand Canyon Railway #239 | HO Scale
Power your favorite regional commuter trains in style with a WalthersMainline F40PH on the job! Built especially for passenger duties, the prototypes entered service in 1976 and many are still going strong today. Based on Phase 2b prototypes, the models feature: One time run of these roadnumbers, limited quantity available - order now! Factory-installed vertical hand rails Molded drill starter points for grab irons (sold separately) RP-25 metal wheels Proto MAX(TM) metal knuckle couplers Fully assembled 21mtc connector ESU Sound for DCC and DC layouts featuring: - 4 function outputs with brightness control by CV - Fully DCC compatible - 14, 28, 128 speed steps - Dual mode DC and DCC - 4 air horns changeable by CVs - 2 bells changeable by CVs - Full 8-notch prime mover sounds - Compressor - Dynamic brake Same powerful drive as WalthersProto(R) locos featuring - Five-pole skew-wound motor - 14:1 gear ratio - Helical-cut gears for quiet operation and easy multiple unit operation - All-wheel drive and electrical pickup - Heavy die-cast metal chassis - Constant and directional LED lights PLEASE NOTE: When operating Walthers-branded DCC-equipped locomotives in DC mode, do not use power packs that exceed an 18V rating. This includes MRC 1300-series power packs which have known issues with our decoders. Alternate horns and bell sounds can be programmed on the sound decoder using these CVs: Horns: CV163 = 0 - Nathan K5LH (default) CV163 = 1 - Nathan K5HLL CV163 = 2 - Nathan K5H CV163 = 3 - Nathan K5LLA Bells: CV164 = 0 - Graham White E-Bell (default) CV164 = 1 - GE Steel Bell More Information Item # 910-19480 Brand WalthersMainline Scale HO Type EMD Diesel Road Name Grand Canyon Railway Road Number 239
£132.66
WalthersMainline Walthers Trainline 910-20432 | EMD GP9 Phase II with Chopped Nose - ESU(R) Sound and DCC - Canadian National #4012 (red, black, white stripes) | HO Scale
PLEASE NOTE: When operating Walthers-branded DCC-equipped locomotives in DC mode, do not use powerpacks that exceed an 18V rating. This includes MRC 1300-series powerpacks, which have known issues with our decoders. WalthersMainline Phase II Chopped Nose GP9 is a must-have model for your 1960s and later diesel roster! Outwardly similar to the earlier GP7, and sharing the same boxy, no frills body with its high, short hood, minor production changes in the number and placement of louvers on locomotives built from 1955 to 1957 resulted in what modelers and railfans refer to as "phase two" GP9s. In the 1960s, many roads began rebuilding their GP9s as an affordable alternative to new equipment, and many were refitted with chopped short hoods to improve forward visibility. Like it's prototypes, many are still going strong today and the WalthersMainline Phase II GP9 with chopped nose is perfect power for any assignment and features: One time run of these roadnumbers - order now, limiyted quantity available! Detailed body with chopped nose Based on Phase II units rebuilt in the 1960s by many owners Scale width hood with correct contours With or without dynamic brakes as appropriate See-through steps Correct RP-25 metal wheels Available with ESU Sound and DCC for DCC or DC layouts featuring: 4 function outputs with brightness control by CV Fully DCC compatible 14, 28 or 128 speed steps Dual mode DC and DCC 4 Airhorns changeable by CVs 2 bells changeable by CVs Full 8-notch prime mover sounds Compressor Dynamic brake Same powerful drive as WalthersProto(R) locos featuring: Five-pole skew-wound motor 14 to 1 gear ratio Helical-cut gears for quiet operation and easy multiple unit operation All-wheel drive and electrical pickup Machined brass flywheel Heavy die-cast metal chassis Constant and directional LED headlights 21-pin DCC plug Molded drill starter points - add grab irons to your model easily with the GP9 Phase II Diesel Detail Kit (#910-258 sold separately) Additional information on DCC functions:ESU CV ListESU Function MappingESU Function Output Alternate Horns and Bells include: Horns: CV163 = 0 - Leslie A-200 (default) CV163 = 1 - Wabco Single Chime CV163 = 2 - Leslie S3L CV163 = 3 - Nathan M5 Bells: CV164 = 0 - EMD Brass Bell (default) CV164 = 1 - EMD Steel Bell
£142.60
WalthersMainline Walthers Trainline 910-20433 | EMD GP9 Phase II with Chopped Nose - ESU(R) Sound and DCC - Canadian National #4013 (red, black, white stripes) | HO Scale
PLEASE NOTE: When operating Walthers-branded DCC-equipped locomotives in DC mode, do not use powerpacks that exceed an 18V rating. This includes MRC 1300-series powerpacks, which have known issues with our decoders. WalthersMainline Phase II Chopped Nose GP9 is a must-have model for your 1960s and later diesel roster! Outwardly similar to the earlier GP7, and sharing the same boxy, no frills body with its high, short hood, minor production changes in the number and placement of louvers on locomotives built from 1955 to 1957 resulted in what modelers and railfans refer to as "phase two" GP9s. In the 1960s, many roads began rebuilding their GP9s as an affordable alternative to new equipment, and many were refitted with chopped short hoods to improve forward visibility. Like it's prototypes, many are still going strong today and the WalthersMainline Phase II GP9 with chopped nose is perfect power for any assignment and features: One time run of these roadnumbers - order now, limiyted quantity available! Detailed body with chopped nose Based on Phase II units rebuilt in the 1960s by many owners Scale width hood with correct contours With or without dynamic brakes as appropriate See-through steps Correct RP-25 metal wheels Available with ESU Sound and DCC for DCC or DC layouts featuring: 4 function outputs with brightness control by CV Fully DCC compatible 14, 28 or 128 speed steps Dual mode DC and DCC 4 Airhorns changeable by CVs 2 bells changeable by CVs Full 8-notch prime mover sounds Compressor Dynamic brake Same powerful drive as WalthersProto(R) locos featuring: Five-pole skew-wound motor 14 to 1 gear ratio Helical-cut gears for quiet operation and easy multiple unit operation All-wheel drive and electrical pickup Machined brass flywheel Heavy die-cast metal chassis Constant and directional LED headlights 21-pin DCC plug Molded drill starter points - add grab irons to your model easily with the GP9 Phase II Diesel Detail Kit (#910-258 sold separately) Additional information on DCC functions:ESU CV ListESU Function MappingESU Function Output Alternate Horns and Bells include: Horns: CV163 = 0 - Leslie A-200 (default) CV163 = 1 - Wabco Single Chime CV163 = 2 - Leslie S3L CV163 = 3 - Nathan M5 Bells: CV164 = 0 - EMD Brass Bell (default) CV164 = 1 - EMD Steel Bell
£142.60
WalthersMainline Walthers Trainline 910-10432 | EMD GP9 Phase II with Chopped Nose - Standard DC - Canadian National #4002 (red, black, white stripes) | HO Scale
WalthersMainline takes the hard work out of modeling one of the most popular prototype diesels ever, with the EMD GP9 Phase II (sometimes referred to as the Phase 2) with Chopped Short Hood in HO Scale! Typical of railroad rebuilds from the 1960s on that are still going strong today, they're nicely detailed, and equipped with the proven power of a WalthersProto(R) drive. Perfect for railroads big or small the WalthersMainline EMD GP9 Phase II with Chopped Short Hood features: One of the most widely used diesels ever - based on Phase II units rebuilt for improved forward visibility and in service from the 1960s to present Limited edition - one time run of these roadnumbers! Scale width hood with correct contours See-through steps Same powerful drive as WalthersProto(R) locos featuring: Five-pole skew-wound motor 14 to 1 gear ratio Helical-cut gears for quiet operation and easy multiple unit operation All-wheel drive and electrical pickup Machined brass flywheel Heavy die-cast metal chassis Constant and directional LED headlights 21-pin DCC plug Molded drill starter points - add grab irons to your model easily with the GP9 Phase II Diesel Detail Kit (#910-258 sold separately) Additional information on DCC functions:ESU CV ListESU Function MappingESU Function Output Alternate horns and bells can be programmed on the sound decoder using these CVs: Horns: CV163 = 0 - Leslie A-200 (default) CV163 = 1 - Wabco single-chime CV163 = 2 - Nathan M3 CV163 = 3 - Leslie S3L Bells: CV164 = 0 - Bronze bell (default) CV164 = 1 - Steel bell
£106.12
WalthersMainline Walthers Trainline 910-10433 | EMD GP9 Phase II with Chopped Nose - Standard DC - Canadian National #4010 (red, black, white stripes) | HO Scale
WalthersMainline takes the hard work out of modeling one of the most popular prototype diesels ever, with the EMD GP9 Phase II (sometimes referred to as the Phase 2) with Chopped Short Hood in HO Scale! Typical of railroad rebuilds from the 1960s on that are still going strong today, they're nicely detailed, and equipped with the proven power of a WalthersProto(R) drive. Perfect for railroads big or small the WalthersMainline EMD GP9 Phase II with Chopped Short Hood features: One of the most widely used diesels ever - based on Phase II units rebuilt for improved forward visibility and in service from the 1960s to present Limited edition - one time run of these roadnumbers! Scale width hood with correct contours See-through steps Same powerful drive as WalthersProto(R) locos featuring: Five-pole skew-wound motor 14 to 1 gear ratio Helical-cut gears for quiet operation and easy multiple unit operation All-wheel drive and electrical pickup Machined brass flywheel Heavy die-cast metal chassis Constant and directional LED headlights 21-pin DCC plug Molded drill starter points - add grab irons to your model easily with the GP9 Phase II Diesel Detail Kit (#910-258 sold separately) Additional information on DCC functions:ESU CV ListESU Function MappingESU Function Output Alternate horns and bells can be programmed on the sound decoder using these CVs: Horns: CV163 = 0 - Leslie A-200 (default) CV163 = 1 - Wabco single-chime CV163 = 2 - Nathan M3 CV163 = 3 - Leslie S3L Bells: CV164 = 0 - Bronze bell (default) CV164 = 1 - Steel bell
£106.12
WalthersTrainline Walthers Trainline 931-2505 | EMD GP15-1 - Standard DC - Union Pacific(R) (yellow, gray, red) | HO Scale
Expand your HO trainset fun in minutes with the WalthersTrainline EMD GP15-1 diesel! Fully assembled and ready for service, features include: Directional headlights All-wheel drive and electrical pick-up Powerful can motor with flywheel Heavy die-cast metal frame for added pulling power Colorful paint and lettering schemes Body-mounted magnetic knuckle couplers RP-25 metal wheels
£54.59