These hand crafted Highway Concrete Barriers HO scale accurate are uniquely designed by Squeaky’s Trains & Things, 100% exclusive and only available from Squeaky’s Trains. Each and every barrier goes through an inspection before and after paint to insure the best quality finish possible. Condition: New Scale: HO Scale Accurate Size Length: 1.36″ / 34.6mm (10ft 1:87) Height:  0.35″ / 9.0mm Width: 0.31″ / 8.0mm Design: Exclusive 3D model designed by Squeaky’s Trains Manufacture: 3D printed with high quality materials Finish/Color: Concrete – hand painted, each barrier is unique and may have variations. Unpainted or un-finished 3D printed models may come in any base color that was available for use at the time of printing. Base color requests are accepted but not always possible to fulfill. Notes: Vehicles, coin, or other props not included.  

Read more less

The LM-4S-G is a module that you can install into a model train locomotive so the locomotive can be controlled and setup by a Ring Engineering RailPro Controller, such as the HC-2 Handheld Controller with a Color Touch Screen! After the LM-4S-G is installed in a locomotive, you will be able to control the locomotive speed, direction, up to 6 light outputs and sounds! The LM-4S-G has “Direct Radio” (RF transceiver) built inside. The built in RF module allows commands and data to be sent and received to and from the module. You can load a picture of your choice into the LM-4S-G module. Then you will be able to touch the screen of the HC-2 to take control of your locomotive! You can even download new sounds and light effects using the built in Direct Radio! Product Specifications: Sound Profile: Universal (all) Dimensions: 3.35 x 1.32 x 0.57 in DCC Track Voltage: 7.5V – 18V Light Outputs 6   Package Contents: LM-4S-G Locomotive Module WH-9 9 Pin Wiring Harness Instruction Sheet The LM-4S-G is equipped with Direct Radio! This allows Ring Engineering Controlling Devices such as the HC-2, Handheld Controller with Color Touch screen, to control and configure your locomotive by sending and receiving data directly to the LM-4S-G through the air by use of RF transmission! The Direct Radio is very fast giving your locomotive quick response to your controls. Further, a controlling device can detect your LM-4S-G with just a few touches on the screen. Because of Direct Radio, you can load a picture of your locomotive to the LM-4S-G! You can also load Sounds, Light Effects and much more!Your LM-4S-G is equipped with Rail Sonic HD Sound System! This is Ring Engineering's technology that allows your LM-4S-G to produce realistic locomotive sounds!Radio Load Sharing is a truly an innovative invention from Ring Engineering. It allows your locomotives that are linked together (sometimes called Consisted or MU'ed) to actually share pulling power. Only RailPro equipped locomotives use Direct Radio to talk to each other to be sure each locomotive pulls its share of the load! Even more amazingly, Ring Engineering's patent pending process only takes seconds to setup!Six light outputs. Can be configured for multiple light effects on a single output including On/Off, Dim, Ditch, Mars, Strobe, and more! Additional light effects can be loaded using DirectRadio!Built in protection with fault reporting by Direct Radio!Tiny size 3.35 x 1.32 x 0.57 Inches for easy fit. Important: If you are running your trains outside be sure to buy the model HC-2-SUN handheld controller instead of the standard model HC-2. The HC-2-SUN is easily readable in sunlight.  The HC-2 screen was designed for indoor use and looks real good inside.  Outside the standard HC-2 screen can look washed out when the sun shines on it.

Read more less

The Woodland Scenics 618 Static Grass Medium Green 4mm is a versatile product designed for enhancing the realism of your model landscapes.  Here are some key features: Color and Texture: This product offers a medium green color, perfect for replicating natural grass in a variety of settings. The 4mm fibers are ideal for modeling longer growth in smaller scales or mowed grass in larger scales. Application: Static Grass is a special material that stands upright when it is applied with the Static King™. It’s part of the Field System, which makes it easy to add texture and dimension while modeling meadows, fields, and pastures. Versatility: You can blend multiple lengths and colors of Static Grass to replicate all phases of growth. It’s suitable for multi-scale use, making it a great choice for various model train scales and other hobby projects. Brand: This product is manufactured by Woodland Scenics, a reputable brand in the model landscape industry. Static Grass 42 grams Grass length: 3mm

Read more less

The Circuitron Tortoise Switch Machine (6 Pack) Motor stalls at each end of throw No cutoff contact necessary Precision engineered gear-drive mechanism Enclosed construction Constant tension on switch points Ultra-Simple Mounting! No additional brackets or linkage necessary Fulcrum adjusts for use in all scales - Z to G. Prototypical Slow Motion Action! 3 seconds to complete the throw Convenient Auxiliary Contacts! 2 sets SPDT provided for powering the frogs or signals

Read more less

Squeaky’s Trains – HO Scale – “Jersey” Concrete Traffic Barriers Our “Jersey” Temporary Concrete Barriers are HO scale accurate, 100% exclusive and only available from Squeaky’s Trains. Each and every barrier goes through an inspection to insure the best quality possible. Condition: New Scale: HO Scale Accurate Sizes Length: See Size Options Height:  0.35″ / 9.0mm Width: 0.31″ / 8.0mm Design: Exclusive 3D model designed by Squeaky’s Trains Manufacture: 3D printed with high quality materials Finish/Color: Unpainted, gray. Notes: Vehicles, coin, or other props not included.  Looking to purchase in bulk? Contact us for pricing.

Read more less

You haven’t heard WOWSound until you’ve heard it through our 28mm High Bass 4W WOWSpeaker! This speaker handles an unprecedented 4 watts of power, and showcases a mighty bass reflex that packs a big sonic punch. Welcome to the new standard for sound in model trains – pick one up today and prepare to be blown away! This speaker is 28mm (1.1″) diameter and 13.5mm (0.53″) thick which includes a rubberized mounting gasket. The mounting gasket allows for unrestricted movement of the cone, preventing distortion or physical damage! Note: Product listing is for 1x speaker. Additional images provided for clarity. Dimensions: 1.1″ diameter x 0.53″ or 28mm diameter x 13.5mm Sound Pressure Level: 84 ± 3.0 dB (A), at 0.63 V, 0.1 m, Average 500,1,000, 2,000, 4,000 (Hz ), at 25°C Effective Frequency Band: 250 Hz. to 20 kHz. Power Rating: 3W (Typical) 4W (Peak) DC Impedance: 4 Ω ; ± 15%, at 1,000 Hz., 1.0 V

Read more less

This snap-together baffle kit is designed for use with SoundTraxx’s 28mm round speakers (P.N. STX810054 or STX810153).

Read more less

The Decoder Buddy Mini was developed to fit into smaller steam and diesel applications.  there has also been interest in HOn3 and S-Gauge applications. This mother board does not include the 21 Pin Decoder. This mother board requires soldering. These printed circuit board is  NOT INTENDED FOR USE IN A DC SYSTEM. Included with board are four axial resistors to be mounted remotely inline and are sized for LEDs. (2.2K) The mother board includes:  One 21 Pin Decoder receptacle Two pairs of track input pads One pair of motor input pads One set of stay alive pads (U+ , GND and if necessary a third control wire ) One pair of speaker pads Resistors for use with LED lighting. (separate axial 2.2K)  (Also available with 0 ohm, 750 ohm and custom specified resistors for function outputs. This accommodates some previously installed and "12 volt LEDs".)  It is IMPORTANT to realize that resistors must be used when LEDs are connected to the four lighting outputs of the Mini!!!  The resistors may be soldered in line when purchased or the included resistors may be soldered inline upon installation.  Remember there are different incandescent lamp voltage requirements and current draw that have to be taken into consideration also. (Until the next batch is produced the Mini will be labeled Tiny and the picture on the package will indicate the correct headlight outputs for direction of locomotive.)

Read more less

This product is versatile in terms of direction of the placement of the board and mounting in various configurations.  It can easily replace a QSI board, a Dual Mode decoder board or be mounted directly on the electric motor or frame with Kapton tape.  (It is recommended that a piece of Kapton tape be placed on the bottom of the mother board to assure electrical isolation from the electric motor or frame.) This mother board does not include a 21 Pin Decoder. This mother board and connector board require soldering. These printed circuit boards are NOT INTENDED FOR USE IN A DC SYSTEM. The on board resistors are sized for LEDs. (1K)  V5 (old) vs V5B (current) The V5 has the capability of easily adding a two wire stay alive.  The U+ and the GND pads are positioned close together and work well.  The three wire stay alive or Power Pack has a third wire that could be connected to pin-1 on the base of the 21-pin connector.  Pin -1 is associated with Aux 10 on a Loksound 5 decoder and used to turn the Power Pack off and on.  It is used frequently but not as easy to solder to as a pad.  I have a video on my Facebook page of the procedure.   The V5B has a dedicated pad for the white control wire of the Power Pack and is labeled "W".  Now there are six pads in the row of soldering pads on the bottom of the board just under the small light connector board in the picture on the right.  They are, right to left; W, U+, GND, A12, A11 and U+.  The other difference is that the "W" pad is connected to pin-2 of the 21-pin connector and the Aux 7 function controls the Power Pack on this board.  It is the default function assigned to the LokSound 5 decoders.  Package Includes: 1x Mother Board 1x Connector Board Dimensions: 0.67" x 2.20" x 0.35" (17 mm x 56 mm x 0.9 mm)The mother board includes;  One 21 Pin Decoder receptacle, Two pairs of track input pads, One pair of motor input pads, One pair of stay alive pads (U+ and GND), Pads for two Aux functions (Version 5 Feature) Two pairs of speaker pads wired in parallel, Resistors for use with LED lighting. (on board 1K)  The connector board contains pads for twelve pairs of lighting function connections. U+ or the blue wire has twelve connected pads for the common power source. The negative (-) discrete function pads are all labeled to indicate their connection to the functions available in the decoder. The lighting connector was designed so that the shell of the diesel locomotive can be easily separated from the frame without un-soldering wires. This does require that the headlight and rear lights be mounted in the shell of the locomotive and that the diesel has a removable dynamic brake shell. Incandescent lamps or bulbs are not well suited for the Decoder Buddys or associated decoders.  It can be done but it will require more electronics to achieve a result.  Our recommendation is to go with LEDs.

Read more less

Tsunami2 meets N-Scale! The TSU-KN1 is our first plug and play Tsunami2 N-Scale decoder. Finally, you can get the Tsunami2 features you have been wanting in your N-Scale locomotives! We are excited to introduce a Plug and Play Tsunami2, N-Scale decoder and installation kit. The new TSU-KN1 is designed to fit into Kato N-Scale E, F-units, F40PH, PA and P42 locomotives. Get an easy install and the amazingly realistic sounds plus the features that all Tsunami2 decoders have to offer.   The TSU-KN1 comes with a complete installation kit ensuring an easy install. Also note that the TSU-KN1 is designed with 4 LED friendly function outputs making external resistors unnecessary! Installation kit includes: TSU-KN1 Decoder Mini Cube 3 Speaker and Baffle  Speaker Wire  Kapton Tape 2 Sunny White LEDs  Product Specifications: Dimensions: 55 x 13.8 x 3.2mm Max. Motor Stall Current: 500mA Max. Function Current: 100mA (each output) Function Outputs: 4 (LED Friendly. No resistors necessary) Audio Amplifier: 1 Watt, 8-Ohm Load DCC Track Voltage: 7.5V – 22V Sound Channels: 16 Tsunami2 Digital Sound Decoders integrate a full-featured sound system, Hyperlight™ lighting effects, Hyperdrive2™ advanced motor control, and a DCC decoder into a single package. Tsunami2 Digital Sound Decoders offer 20+ lighting effects in each model! Other popular Tsunami2 features include: Reactive Dynamic Digital Exhaust, Functioning locomotive and train brakes. We also offer a large selection of selectable sound effects including: 8 manufacturer specific prime movers, bells (12), airhorns (40+), couplers, compressors, and more!

Read more less

The HC-3-SUN with an Extra Bright Screen for use in outdoor environments and sunlight, is a wireless controller with a color touch screen that can be used to operate your model railroad layout. The HC-3 can control the speed, direction, lights, and sounds of locomotives and other accessories by simply touching the screen! RailPro products are equipped with Direct Radio and are designed to work together. Direct Radio allows the RailPro components to communicate with each other without any wires! Direct Radio is very fast giving your RailPro products quick response to your controls. You will need to install RailPro modules into your locomotives and accessories that you want to control. The color graphic screens make it so simple to use, that most users will find it unnecessary to use the manual to even setup advance features. Product Specifications: Dimensions: 6.1 x 3.4 x 1.5 in   Simply touch the screen to take control of a locomotive or accessory, adjust settings and much more!Direct Radio allows RailPro components to communicate with each other without any wires! Direct Radio is very fast giving your RailPro products quick response to your commands. Also, Direct Radio has two-way communication that allows your HC-3 to transmit and receive information!Setting up your RailPro system is easy. When you buy new RailPro Ready products, or new RailPro modules for locomotives and accessories, simply press the “Find Product” button and the HC-3 will automatically load a picture of the product. You can take control of the product by touching the picture of the product!With a couple touches on the screen, you can link multiple locomotives together for more pulling power! With one more touch, you can unlink the locomotives. Our Direct Radio technology allows the locomotives to communicate together to ensure each locomotive pulls its share of the load.Multiple HC-3’s can be used at the same time to allow additional family and friends to enjoy your model layout! Also, multiple locomotives and other accessories can be used simultaneously for complete model layout control!The HC-3 comes complete with built in rechargeable batteries. The HC-3 is equipped with USB port to connect to a PC. You can go to Ring Engineering’s Internet site and download new pictures, sounds, and even new programs to add more functionality to your RailPro system. You do not need a computer to use the HC-3, but this can prove to be a very useful feature.

Read more less