DCC Decoders

By default, this decoder does not come with a pre-programmed Sound Profile. Nevertheless, we provide complimentary Sound File programming for all ESU decoders. Please be aware that opting for Sound File Programming in your order might result in a shipment delay of 1 to 2 business days. Visit this link to preview ESU Sounds 8-Pin NEM652 Harness Plug, 30 x 15.5mm Version The LokSound 5 is the most important member of the LokSound family. Due to the combination of the digital decoder and the sound module on one circuit board we achieve the smallest possible dimensions of 30 mm x 15.5 mm. Therefore it fits into almost any H0 or 0 gauge locomotive. LokSound 5 decoders are available with all popular interface types and are supplied with a sugar cube speaker (11 mm x 15 mm) and a sound enclosure. The LokSound 5 DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Please note the LokSound 5 DCC decoder does not come with a speaker. Operating modes Like all products of the LokSound family the LokSound 5 is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations. This decoder supports all DCC programming modes and thanks to RailCom® you may read out the CV values on the main, provided you have a command station supporting RailCom®. There are utility registers for command stations that only facilitate programming of CVs ranging from 1 to 255. Motorola® users benefit from up to 28 speed steps for 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. An integral programming mode even allows programming with the good old Central Unit 6021. The M4 protocol supports the automatic registration on mfx® compatible central units. The LokSound 5 decoder supports the Märklin® braking sections just as well as the ZIMO® HLU braking commands or the Lenz® ABC system. Braking with DCC brake generators or with DC is also possible. Furthermore the locomotive with a LokSound will come to a halt when a Selectrix® braking diode is switched into the circuit. The ABC push-pull feature enables the automatic commuting between two stations. The LokSound 5 decoder is also suitable for analogue DC and AC (!) layouts. Sound The LokSound 5 decoder can reproduce up to 10 channels simultaneously. Each channel offers up to 16 Bit / 31250 kHz and thus we have finally achieved hi-fi sound quality on your layout. For all practical purposes one cannot detect any difference to the original. A class D audio power amplifier with up to 3W output power feeds the speakers with a permitted impedance of 4 – 32 Ohms. The huge 128 MBit sound memory assures sufficient storage capacity. The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles. Functions We are quite aware that you want your locomotives to be as realistic as possible. Therefore we have packed many function outputs into it.  Subject to the type of interface every LokSound 5 has at least 10 amplified outputs. The decoders with PluX22 or 21MTC interface have an additional 4 outputs for controlling servos or as logic outputs. Of course, all important lighting functions are supported. The brightness of each output may be adjusted separately. The decoder supports the automatic push and pull movements – known as the coupler waltz - required for reliable operation of digital couplers such as the ones by ROCO® and Krois® as well as Telex® couplers. Motor control Motor control of the LokSound 5 has been further improved. A variable PWM pulse frequency ranging from 10 kHz to 50 kHz assures perfect silent operation, particularly for coreless motors. Thus the typical hum is a thing of the past. Load control can now be adjusted with up to 10 separate CVs and thus will manage even the most difficult cases. The unique “Auto Tune” function facilitates the automatic calibration of the decoder to perfectly match the motor. The LokSound 5 decoder supplies up to 1.5A motor current, which is quite sufficient even for older motor types. LokSound 5 DCC The LokSound 5 DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. More Information Item # 58420 Brand ESU Scale HO & O WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

Blunami will change the way you enjoy the model railroading hobby! The Blunami BLU-4408The BLU-4408 is designed to wirelessly operate models with higher stall currents such as some S, O, and large scale locomotives; this decoder features easy-to-use terminal blocks for no-fault wiring and a higher audio amplifier for awesome volume, indoors or out. Blunami decoders can be operated in three different ways: DC, DCC and Wireless mode. Using the Blunami app (iOS versions 8 or later), you can operate your locomotive with incredible ease of use. You will feel like you are in the cab with the amazing new features that Tsunami2 has to offer including: Reactive Dynamic Digital Exhaust, Functioning locomotive and train brakes, injectors, power reverse, and firebox flicker. We also offer a large selection of selectable sound effects including: exhaust chuffs(10), prime movers (up to 12), bells (12), Whistles (90), airhorns (40+), couplers, dynamos and more! DYNAMIC DIGITAL EXHAUST For added realism, you’ll love our reactive Dynamic Digital Exhaust (DDE) feature. When your locomotive is traveling across flat terrain and simply maintaining speed, you will hear your locomotive chugging along. But, when the locomotive encounters a grade and the engineer applies more throttle to get the train up the hill, the engine sounds will automatically react and reflect the increase of power needed to crest the hill. DDE accomplishes this by calculating the changes in strain or load on the motor and adjusting the exhaust to appropriately simulate the work the engineer would be doing to the throttle of the engine. This gives Tsunami2 the ability to create the most realistic experience possible.HIGH QUALITY SOUND LIBRARYOur large selection of high quality sound effects include:  10 Exhaust Chuffs Up to 12 Prime Movers in each sound profile  Up to 12 Bells  90 Whistles 40+ Airhorns Additional couplers, dynamos, cab chatter and more! ADDED REALISMAdditional realism can be simulated by adding functioning locomotive and train brakes, injectors, power reverse, firebox flicker and more. EASY INSTALLATIONNo soldering required! This decoder features easy-to-use terminal blocks for no-fault wiring. This 4-amp, universal-style format decoder includes a connector to easily add a CurrentKeeper (P.N. 810140 or 810160) to maintain performance over dirty track and switches. Dimensions: 69 x 30.5 x 14mm  Max. Motor Stall Current: 4A Max. Function Current: 400mA (each output) Function Outputs: 8 Audio Amplifier: 3 Watt, 8-Ohm Load DCC Track Voltage: 7.5V – 26V Sound Channels: 16   Blunami Owner's Manual Blunami Installation Guide Blunami Steam User's Guide Blunami Diesel User's Guide Blunami Electric User's Guide   Blunami Sound Selection References: Blunami Steam-2 Sound Selection Reference Blunami EMD Sound Selection Reference Blunami EMD-2 Sound Selection Reference Blunami GE Sound Selection Reference Blunami ALCO Sound Selection Reference Blunami Baldwin & Others Sound Selection Reference Blunami Electric Sound Selection Reference   Blunami Sound Samples Blunami Steam-2 Sounds Blunami EMD Blunami EMD-2 Sounds Blunami GE Sounds Blunami ALCO Sounds Blunami Baldwin & Other Diesel Sounds Blunmai Electric Sounds SoundTraxx A true pioneer in the model train industry, SoundTraxx has been creating innovative products for the discriminating model railroader since 1990. We proudly design and manufacture our industry-best products right here in the USA, and our friendly customer support staff work side-by-side with the rest of our product team.

Read more less

The TSU-4400 is designed for models with higher stall currents such as some S, O, and large scale locomotives; this decoder features easy-to-use terminal blocks for no-fault wiring and a higher audio amplifier for awesome volume, indoors or out. You will feel like you are in the cab with the amazing new features that Tsunami2 has to offer including: Reactive Dynamic Digital Exhaust, Functioning locomotive and train brakes, injectors, power reverse, and firebox flicker. We also offer a large selection of selectable sound effects including: exhaust chuffs(10), prime movers (up to 12), bells (12), Whistles (90), airhorns (40+), couplers, dynamos and more! This 4-amp, universal-style format decoder includes a connector to easily add a CurrentKeeper (P.N. STX810140) to maintain performance over dirty track and switches. Product Specifications: Sound Profile: GE Diesel Dimensions: 69 x 30.5 x 14mm Max. Motor Stall Current: 4A Max. Function Current: 400mA (each output) Function Outputs: 6 Audio Amplifier: 3 Watt, 8-Ohm Load DCC Track Voltage: 7.5V – 26V Sound Channels: 16

Read more less

The TSU-4400 is designed for models with higher stall currents such as some S, O, and large scale locomotives; this decoder features easy-to-use terminal blocks for no-fault wiring and a higher audio amplifier for awesome volume, indoors or out. You will feel like you are in the cab with the amazing new features that Tsunami2 has to offer including: Reactive Dynamic Digital Exhaust, Functioning locomotive and train brakes, injectors, power reverse, and firebox flicker. We also offer a large selection of selectable sound effects including: exhaust chuffs(10), prime movers (up to 12), bells (12), Whistles (90), airhorns (40+), couplers, dynamos and more! This 4-amp, universal-style format decoder includes a connector to easily add a CurrentKeeper (P.N. STX810140) to maintain performance over dirty track and switches. Product Specifications: Sound Profile: ALCO Diesel Dimensions: 69 x 30.5 x 14mm Max. Motor Stall Current: 4A Max. Function Current: 400mA (each output) Function Outputs: 6 Audio Amplifier: 3 Watt, 8-Ohm Load DCC Track Voltage: 7.5V – 26V Sound Channels: 16

Read more less

Maximize the performance of your N scale model trains with the Digitrax DN167N18 mobile decoder. This plug-in Next18 decoder offers advanced control and smooth operation, enhancing the realism of your layout. With its compact design and easy installation, it's the perfect upgrade for your locomotives. Mobile Decoder Fits Next18 socket locomotives Plug-in Next18 connector Motor drive at connector capacity 6 FX3 Functions More Information Item # DN167N18 Brand Digitrax Scale N MSRP $36.00 TCA Grading C-10 Mint - Brand New Availability In-Stock/Restockable Manuals Instruction Sheet

Read more less

By default, this decoder does not come with a pre-programmed Sound Profile. Nevertheless, we provide complimentary Sound File programming for all ESU decoders. Please be aware that opting for Sound File Programming in your order might result in a shipment delay of 1 to 2 business days. Visit this link to preview ESU Sounds The LokSound 5 micro DCC Direct Kato USA has been specially developed for installation in track N vehicles of the Kato USA brand: Most diesel locomotives of this manufacturer are installed in the American model of these decoders instead of the analog board installed as standard. Finally, these models can also be easily retrofitted with a LokSound decoder. The LokSound 5 micro DCC Direct Kato USA with its dimensions of 60.0mm x 10.1mm is a pure DCC decoder and comes without a loudspeaker. Modes The LokSound 5 micro DCC Direct Kato USA is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders log in fully to a suitable digital center.It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokSound 5 micro DCC Direct Kato USA Decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake blocks or dc voltage is also possible. In addition, it also stops with a Selectrix® brake diode. An AUTOMATIC ABC commuter train allows automatic commuting between two stations. The LokSound 5 micro DCC Direct Kato USA can be used on analog DC webs.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Sound The LokSound 5 micro DCC Direct Kato USA Decoder can play up to 12 channels simultaneously. Each channel can be resolved with up to 16 bits / 31250 kHz and offers hi-fi quality on its system. There is virtually no difference to the original audible anymore. A Class-D audio output with up to 3W output power controls the speakers, which can have between 4 ohms and 32 ohms impedance. A 128 Mbit sound memory provides enough capacity. All individual noises can be adjusted individually in the volume. The super-flexible sound engine without a rigid schedule allows the exemplary simulation of all conceivable rail tracks. Functions Despite its compact dimensions, the LokSound 5 micro DCC Direct Kato USA is equipped with an enormen number of function outputs. Two directly soldered SMD LEDs are designed for front and rear front and rear head lighting. For older models, two wired LEDs can alternatively be soldered and switched separately. Three further reinforced function outputs are also available. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokSound 5 micro DCC Direct Kato USA has a variable PWM clock frequency from 10kHz to 50kHz, which ensures super-quiet operation, especially for bell anchor motors – the typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. The LokSound 5 micro DCC Direct Kato USA decoder delivers up to 0.9A motor power. Operational reliability A PowerPack can be connected to the LokSound 5 micro DCC Direct Kato USA on request to bridge dirty rail sections. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. More Information Item # 58741 Brand ESU Scale N WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

By default, this decoder does not come with a pre-programmed Sound Profile. Nevertheless, we provide complimentary Sound File programming for all ESU decoders. Please be aware that opting for Sound File Programming in your order might result in a shipment delay of 1 to 2 business days. Visit this link to preview ESU Sounds  Single Wires Version With the LokSound 5 Nano DCC, ESU has succeeded in developing an even smaller LokSound decoder: With only 19.6 mm x 8.5 mm x 3.2 mm (5.3 mm with single wires), it is the smallest LokSound decoder we have ever built. Thus, it should really be used in all vehicles of nominal sizes N and TT. The LokSound 5 Nano DCC decoder is a pure DCC decoder with opencable ends for free wiring or an E24-interface. The LokSound 5 Nano DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Please note the LokSound 5 Nano DCC decoder does not come with a speaker. Modes The LokSound 5 Nano is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders register fully automatically at a suitable digital center.It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokSound 5 Nano Decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake blocks or with equal voltage is also possible. In addition, it also stops with a Selectrix® brake diode. An automatic ABC pen train allows automatic commuting between two stations. The LokSound 5 Nano can be used on analog DC webs. The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Sound The LokSound 5 Nano Decoder can play up to 12 channels simultaneously. Each channel can be resolved with up to 16 bits / 31250 kHz and offers hi-fi quality on your system. There is virtually no difference to the original audible anymore. A Class-D audio output with up to 3W output power controls the speakers, which may have between 4 ohms and 32 ohms impedance. A 128 Mbit sound memory provides enough capacity.All individual noises can be adjusted individually in the volume. The super-flexible sound engine without a rigid schedule allows the exemplary simulation of all conceivable rail tracks. Functions Despite its small size, the LokSound 5 Nano has 6 reinforced function outputs as well as a logic level output as a solder pad. All important lighting functions are available. The brightness of each output can be set separately. The decoder controls the automatic start-up and disconnection when uncoupling for ROCO®, Krois® and Märklin telex ® couplings. Motor The motor control of the LokSound 5 Nano has a variable PWM clock frequency from 10kHz to 50kHz, which ensures super-quiet operation, especially for bell anchor motors – the typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. The LokSound 5 Nano DCC Direct Decoder delivers up to 0.75A motor power. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. More Information Item # 58923 Brand ESU Scale N WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

By default, this decoder does not come with a pre-programmed Sound Profile. Nevertheless, we provide complimentary Sound File programming for all ESU decoders. Please be aware that opting for Sound File Programming in your order might result in a shipment delay of 1 to 2 business days. Visit this link to preview ESU Sounds LokSound 5 Micro Sound and DCC Control Decoder - Single Wires Version The LokSound 5 micro is a “little wonder”: With only 21mmx10mm footprint, it is by far one of the smallest LokSound decoders we’ve ever built. Thus it should fit into all N gauge and TT vehicles, but is also suitable for small H0 vehicles. All LokSound decoders are equipped with a Next18 interface and are available with adapter plugs to suit all popular digital interface types.  The LokSound 5 micro DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Please note the LokSound 5 DCC decoder does not come with a speaker. Operating modes The LokSound 5 micro is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations. This decoder supports all DCC programming modes and thanks to RailCom® you may read out the CV values on the main, provided you have a command station supporting RailCom®. There are utility registers for command stations that only facilitate programming of CVs ranging from 1 to 255. Motorola® users benefit from up to 28 speed steps for 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. An integral programming mode even allows programming with the good old Control Unit 6021. The M4 protocol supports the automatic registration on mfx® compatible central units. The LokSound  decoder supports the Märklin® braking sections just as well as the ZIMO® HLU braking commands or the Lenz® ABC system. Braking with DCC brake generators or with DC is also possible. Furthermore the locomotive with a LokSound will come to a halt when a Selectrix® braking diode is switched into the circuit. The ABC push-pull feature enables the automatic commuting between two stations. The LokSound 5 micro decoder is also suitable for analogue DC and AC (!) layouts. Sound The LokSound 5 micro decoder can reproduce up to 10 channels simultaneously. Each channel offers up to 16 Bit / 31250 kHz and thus we have finally achieved hi-fi sound quality on your layout. For all practical purposes one cannot detect any difference to the original. A double class D audio power amplifier with up to 3W output power feeds the speakers with a permitted impedance of 4 – 32 Ohms. The huge 128 MBit sound memory assures sufficient storage capacity. The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles. The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles. Functions Despite its small dimensions the LokSound 5 micro decoder has at least 6 amplified function outputs as well as one logic output. There are two more logic outputs on the Next18 interface, which alternately may be employed to control RC servos. Of course, all important lighting functions are supported. The brightness of each output may be adjusted separately. The decoder supports the automatic push and pull movements – known as the coupler waltz - required for reliable operation of digital couplers such as the ones by ROCO® and Krois® as well as Telex® couplers. Motor control Motor control of the LokSound 5 micro has been further improved. A variable PWM pulse frequency ranging from 10 kHz to 50 kHz assures perfect silent operation, particularly for coreless motors. Thus the typical hum is a thing of the past. Load control can now be adjusted with up to 10 separate CVs and thus will manage even the most difficult cases. The unique “Auto Tune” function facilitates the automatic calibration of the decoder to perfectly match the motor. The LokSound 5 micro decoder supplies sufficient motor current (up to 0.75 A) for the intended applications. LokSound 5 micro DCC The LokSound 5 Micro DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. More Information Item # 58823 Brand ESU Scale N & HO WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

Blunami will change the way you enjoy the model railroading hobby! The Blunami BLU-2200The BLU-2200 is a universal-style sound decoder that can be operated in three different ways: DC, DCC and Wireless mode. Using the Blunami app (iOS versions 8 or later), you can operate your locomotive with incredible ease of use. This decoder is suitable for use in both HO and small S-scale models. Wireless mode not currently available for android devices. DYNAMIC DIGITAL EXHAUST For added realism, you’ll love SoundTraxx's reactive Dynamic Digital Exhaust (DDE) feature that automatically notches your models engine up or down depending on the load on the motor. With the Blunami App, DDE calibration has never been easier. When your locomotive is traveling across flat terrain and simply maintaining speed, you will hear your locomotive chugging along. But, when the locomotive encounters a grade and the engineer applies more throttle to get the train up the hill, the engine sounds will automatically react and reflect the increase of power needed to crest the hill. DDE accomplishes this by calculating the changes in strain or load on the motor and adjusting the exhaust to appropriately simulate the work the engineer would be doing to the throttle of the engine. This gives Blunami the ability to create the most realistic experience possible. HIGH QUALITY SOUND LIBRARYSoundTraxx's large selection of high quality sound effects include:  10 Exhaust Chuffs Up to 12 Prime Movers in each sound profile  Up to 12 Bells  90 Whistles 40+ Airhorns Additional couplers, dynamos, cab chatter and more! ADDED REALISMAdditional realism can be simulated by adding functioning locomotive and train brakes, injectors, power reverse, firebox flicker and more. EASY INSTALLATIONThe BLU-2200 can simply plug into models equipped with a DCC quick plug. Our 9-Pin JST to NMRA 8-Pin Wiring Harness (P.N. 810135) can also be used to plug the BLU-2200 into models equipped with an NMRA 8-Pin plug. The BLU-2200 can also be wired into a large variety of models. This 2-amp, universal-style format, and includes a connector to easily add a CurrentKeeper (P.N. 810140 or 810160) to maintain performance over dirty track and switches. Dimensions: 41.9 x 18.8 x 6.8mm  Max. Motor Stall Current: 2A Max. Function Current: 100mA (each output) Function Outputs: 6 Audio Amplifier: 2 Watt, 8-Ohm Load DCC Track Voltage: 7.5V – 22V Sound Channels: 16   Blunami Owner's Manual Blunami Installation Guide Blunami Steam User's Guide Blunami Diesel User's Guide Blunami Electric User's Guide   Blunami Sound Selection References: Blunami Steam-2 Sound Selection Reference Blunami EMD Sound Selection Reference Blunami EMD-2 Sound Selection Reference Blunami GE Sound Selection Reference Blunami ALCO Sound Selection Reference Blunami Baldwin & Others Sound Selection Reference Blunami Electric Sound Selection Reference   Blunami Sound Samples Blunami Steam-2 Sounds Blunami EMD Blunami EMD-2 Sounds Blunami GE Sounds Blunami ALCO Sounds Blunami Baldwin & Other Diesel Sounds Blunmai Electric Sounds SoundTraxx A true pioneer in the model train industry, SoundTraxx has been creating innovative products for the discriminating model railroader since 1990. We proudly design and manufacture our industry-best products right here in the USA, and our friendly customer support staff work side-by-side with the rest of our product team.

Read more less

Blunami will change the way you enjoy the model railroading hobby! The Blunami BLU-2200The BLU-2200 is a universal-style sound decoder that can be operated in three different ways: DC, DCC and Wireless mode. Using the Blunami app (iOS versions 8 or later), you can operate your locomotive with incredible ease of use. This decoder is suitable for use in both HO and small S-scale models. Wireless mode not currently available for android devices. DYNAMIC DIGITAL EXHAUST For added realism, you’ll love SoundTraxx's reactive Dynamic Digital Exhaust (DDE) feature that automatically notches your models engine up or down depending on the load on the motor. With the Blunami App, DDE calibration has never been easier. When your locomotive is traveling across flat terrain and simply maintaining speed, you will hear your locomotive chugging along. But, when the locomotive encounters a grade and the engineer applies more throttle to get the train up the hill, the engine sounds will automatically react and reflect the increase of power needed to crest the hill. DDE accomplishes this by calculating the changes in strain or load on the motor and adjusting the exhaust to appropriately simulate the work the engineer would be doing to the throttle of the engine. This gives Blunami the ability to create the most realistic experience possible. HIGH QUALITY SOUND LIBRARYSoundTraxx's large selection of high quality sound effects include:  10 Exhaust Chuffs Up to 12 Prime Movers in each sound profile  Up to 12 Bells  90 Whistles 40+ Airhorns Additional couplers, dynamos, cab chatter and more! ADDED REALISMAdditional realism can be simulated by adding functioning locomotive and train brakes, injectors, power reverse, firebox flicker and more. EASY INSTALLATIONThe BLU-2200 can simply plug into models equipped with a DCC quick plug. Our 9-Pin JST to NMRA 8-Pin Wiring Harness (P.N. 810135) can also be used to plug the BLU-2200 into models equipped with an NMRA 8-Pin plug. The BLU-2200 can also be wired into a large variety of models. This 2-amp, universal-style format, and includes a connector to easily add a CurrentKeeper (P.N. 810140 or 810160) to maintain performance over dirty track and switches. Dimensions: 41.9 x 18.8 x 6.8mm  Max. Motor Stall Current: 2A Max. Function Current: 100mA (each output) Function Outputs: 6 Audio Amplifier: 2 Watt, 8-Ohm Load DCC Track Voltage: 7.5V – 22V Sound Channels: 16   Blunami Owner's Manual Blunami Installation Guide Blunami Steam User's Guide Blunami Diesel User's Guide Blunami Electric User's Guide   Blunami Sound Selection References: Blunami Steam-2 Sound Selection Reference Blunami EMD Sound Selection Reference Blunami EMD-2 Sound Selection Reference Blunami GE Sound Selection Reference Blunami ALCO Sound Selection Reference Blunami Baldwin & Others Sound Selection Reference Blunami Electric Sound Selection Reference   Blunami Sound Samples Blunami Steam-2 Sounds Blunami EMD Blunami EMD-2 Sounds Blunami GE Sounds Blunami ALCO Sounds Blunami Baldwin & Other Diesel Sounds Blunmai Electric Sounds SoundTraxx A true pioneer in the model train industry, SoundTraxx has been creating innovative products for the discriminating model railroader since 1990. We proudly design and manufacture our industry-best products right here in the USA, and our friendly customer support staff work side-by-side with the rest of our product team.

Read more less

Enjoy complimentary shipping!Bundle your purchases for even more savings with our free shipping option. (This offer is optional) This decoder features a true UP Big Boy recording! Previously this sound file was only offered in Athearn factory installed decoders, but now you can get it on our web store. This decoder is available in 3 board formats: TSU-1100, TSU-2200, and TSU-21PNEM8. We will have more web special decoders in the future so stay tuned. You will also get all of the features that you know and love from our Tsunami2 decoder line including: Reactive Dynamic Digital Exhaust, Functioning locomotive and train brakes, injectors, power reverse, and firebox flicker. We also offer a large selection of selectable sound effects including: bells (12), Whistles (90+), couplers, dynamos and more!These decoders include an optional capacitor or can be wired to a CurrentKeeper (P.N. 810140 or 810160) to maintain performance over dirty track and switches.

Read more less

Enjoy complimentary shipping!Bundle your purchases for even more savings with our free shipping option. (This offer is optional) A true pioneer in the model train industry, SoundTraxx has been creating innovative products for the discriminating model railroader since 1990. We proudly design and manufacture our industry-best products right here in the USA, and our friendly customer support staff work side-by-side with the rest of our product team. The Tsunami2 TSU-BigSteamThe TSU-Big Steam is a limited edition decoder available in 3 board formats. This decoder features a true UP Big Boy recording! Previously this sound file was only offered in Athearn factory installed decoders, but now you can get it on our web store. This decoder is available in 3 board formats: TSU-1100, TSU-2200, and TSU-21PNEM8. You will also get all of the features that you know and love from our Tsunami2 decoder line including: Reactive Dynamic Digital Exhaust, Functioning locomotive and train brakes, injectors, power reverse, and firebox flicker. We also offer a large selection of selectable sound effects including: bells (12), Whistles (90+), couplers, dynamos and more! DYNAMIC DIGITAL EXHAUST For added realism, you’ll love our reactive Dynamic Digital Exhaust (DDE) feature. When your locomotive is traveling across flat terrain and simply maintaining speed, you will hear your locomotive chugging along. But, when the locomotive encounters a grade and the engineer applies more throttle to get the train up the hill, the engine sounds will automatically react and reflect the increase of power needed to crest the hill. DDE accomplishes this by calculating the changes in strain or load on the motor and adjusting the exhaust to appropriately simulate the work the engineer would be doing to the throttle of the engine. This gives Tsunami2 the ability to create the most realistic experience possible.HIGH QUALITY SOUND LIBRARYOur large selection of high quality sound effects include:  10 Exhaust Chuffs Up to 12 Prime Movers in each sound profile  Up to 12 Bells  90 Whistles 40+ Airhorns Additional couplers, dynamos, cab chatter and more! ADDED REALISMAdditional realism can be simulated by adding functioning locomotive and train brakes, injectors, power reverse, firebox flicker and more. EASY INSTALLATIONThe TSU-2200 can simply plug into models equipped with a DCC quick plug. Our 9-Pin JST to NMRA 8-Pin Wiring Harness (P.N. 810135) can also be use to plug the TSU-2200 into models equipped with an NMRA 8-Pin plug. The TSU-2200 can also be wired into a large variety of models. The TSU-21PNEM8 simply plugs into models equipped with a 21-pin NEM socket. These decoders include an optional capacitor or can be wired to a CurrentKeeper (P.N. 810140 or 810160) to maintain performance over dirty track and switches.

Read more less