DCC Accessories

This Digitrax STAW Stow Away Throttle Holder is the perfect solution for storing and organizing your throttle controls. With its compact design and easy installation, it allows for efficient use of space and quick access to your throttles. Keep your workspace clutter-free and your throttles within reach with this 1 pack stow away holder. Bracket will hold: DT602, UT6 and other legacy Digitrax throttles. Access to LocoNet & Power Ports when stowed away. Stores throttle when not in use or when charging. Fascia mounted. Durable design. Easy to install. 90 Day Warranty On Materials & Workmanship Only. More Information Item # STAW Brand Digitrax Warranty No Worries Warranty (read more) MSRP $14.00 TCA Grading C-10 Mint - Brand New Availability In-Stock/Restockable Manuals Instruction Sheet

Read more less

The new ESU PowerPack Mini can be wired to all fourth and fifth generation ESU decoders. It reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders. With its energy storage (1 Farad capacity) the unit supplies power to all light and motor functions as well as to the sound module. Subject to the energy consumption of your model it may continue to move for up to three seconds. The PowerPack Mini incorporates an integral charging circuit controlled by the decoder. Therefore it may be connected even during programming. In order to avoid an undue load on the booster in case there are several models in the same booster sector, the charging current is limited. The buffer time can be reduced by means of a CV. This may be useful to assure the correct stopping position ahead of signals showing the “Stop” aspect (red signal). Although it is considerably smaller than its predecessor, the space requirements of the PowerPack Mini of about 15.7 mm x 9.7 mm x 13 mm must be taken into account when installing this unit. A three-pole wire harness connects the PowerPack Mini to the decoder. The wires are already soldered to the PowerPack Mini and must be soldered to the appropriate solder pads of the decoder. More Information Item # 54671 Brand ESU Scale Multi WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

Digitrax LNCCMC1 Coiled Cord & RJ12 Modular Adapter makes it easy to add a coiled cord to your LocoNet throttle without soldering. Designed for use with all Digitrax throttles, this convenient adapter plugs directly into your existing throttle plug and adds a flexible coiled cord for improved usability and layout comfort. Adds a coiled cord to your LocoNet throttle No soldering required Includes RJ12 modular adapter Compatible with all Digitrax throttles Ideal for upgrading straight cord throttles More Information Brand Digitrax Model Number LNCCMC1 Product Type LocoNet Accessory Compatibility All Digitrax Throttles MSRP $18.00 Warranty 90 Day Limited Warranty HS Code 9503.00.00 Frequently Asked Questions Does this require soldering?No. The LNCCMC1 plugs directly into your existing throttle connection using the included modular adapter. Will this work with older Digitrax throttles?Yes. It is compatible with all Digitrax LocoNet throttles. What does this improve?It replaces or adds a coiled cord for better flexibility and strain relief compared to straight cords.

Read more less

The new ESU PowerPack Maxi has been developed as the powerful complement to the LokSound L V4.0 /  LokSound  5 L decoder. It can, of course, provided there is sufficient space, also be connected to all LokPilot V4.0, LokSound V4.0, LokSound V4.0 M4, LokPilot 5 or LokSound 5 decoders. It provides uninterrupted power to your locomotive when traversing dirty track and long turnout ladders. All sound, lighting and motor functions are buffered with the aid of two energy storage capacitors enabling your models – subject to the total energy consumption - to continue running for up to three seconds. The PowerPack Maxi incorporates an integral charging circuit controlled by the decoder. Therefore it may be connected even during programming. The charging current is limited in order to avoid an undue load on the booster, in case there are several models in the same booster sector. The buffer time can be reduced by means of a CV. This may be useful to assure the correct stopping position ahead of signals showing the “Stop” aspect (red signal). The space requirements of the PowerPack Maxi of about 27.5 mm x 15.7 mm x 13 mm must be taken into account when installing this unit. A three-pole wire harness connects the PowerPack Maxi to the decoder. The wires are already soldered to the PowerPack Maxi but must be soldered to the appropriate solder pads of the decoder. Please note that due to technical reasons the PowerPack cannot operate in analogue mode: Buffering is therefore not possible in analogue mode. More Information Item # 54672 Brand ESU Scale Multi WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

Throttles get put down on the layout, on the scenery, or on the floor. The Digitrax STAW4 is a four-pack of fascia-mounted brackets that give every throttle somewhere to live - stowed, out of the way, and still plugged into LocoNet so it keeps charging between sessions. More LocoNet gear? Browse our DCC Accessories, DCC Wiring, and the full Digitrax range. Features Four brackets per pack - enough to give each operating position its own throttle station. Holds DT602, UT6 and other legacy Digitrax throttles, so it works across a mixed throttle fleet. LocoNet and power ports stay accessible while stowed, which means the throttle can charge in its bracket rather than on a shelf somewhere. Fascia mounted and easy to install - a few screws at each operating position. Durable construction, built to survive being grabbed at during an operating session. More Information Brand Digitrax Item Number STAW4 Product Type Throttle Holder Scale All scales Quantity 4 brackets Fits DT602, UT6 and other legacy Digitrax throttles Mounting Fascia Ports LocoNet and power accessible when stowed Warranty 90 day, materials and workmanship Condition New FAQ Will it hold my throttle?It is designed around the DT602 and UT6, and also holds other legacy Digitrax throttles. If you run a mixed fleet from different eras, check the older ones against the bracket before buying a set for the whole layout. Can the throttle charge while it is in the bracket?Yes - the LocoNet and power ports stay accessible when stowed, so a throttle left in its holder can keep charging between sessions. Where should I mount them?One at each operating position, at a height where an operator can drop a throttle in without looking. Near a universal panel is the usual choice so the cable run is short. How do they attach?They are fascia mounted with screws. Pick a spot on the fascia clear of the layout edge so a stowed throttle is not in the way of anyone leaning in.

Read more less

The Train Control Systems KA4 Keep-Alive® is a compact stay-alive capacitor pack that feeds backup power to your DCC decoder whenever the wheels lose contact with the rails. No more stalling on dirty track, dead frogs, or insulated turnouts — the KA4 keeps a locomotive running with its lights and sound on for roughly 6 to 20 seconds during a power interruption (depending on the locomotive and motor). It includes Blue and Black-with-White-stripe lead wires to solder to your decoder's keep-alive pads (V+ and ground), so it works with TCS and most other-brand decoders that accept an external keep-alive. Browse more decoder add-ons in our DCC Accessories collection, shop the full Train Control Systems lineup, or pair it with a new sound decoder from our DCC Decoders collection. Features Keep-Alive® stay-alive capacitor pack eliminates stalling on dirty track, dead frogs, and insulated rail joints. Powers an HO locomotive with lights on for approximately 6 to 20 seconds during a power interruption. Includes Blue and Black/White lead wires to solder to your decoder's keep-alive pads — works with TCS and most other-brand decoders. Dimensions: .52" x .52" x .45" (13.22 x 13.22 x 11.55 mm). Input rating 12–16V; works with any scale and any DCC system. More Information Brand Train Control Systems (TCS) Item Number 1668 (KA4) Type Keep-Alive / Stay-Alive Capacitor Pack Connection Blue + Black/White Wire Leads (solder-on) Dimensions .52" x .52" x .45" (13.22 x 13.22 x 11.55 mm) Input Rating 12–16V Scale Any Scale Condition New FAQ What does a Keep-Alive actually do?It stores an electrical charge and feeds it to your decoder when track power drops out, so the locomotive keeps moving and its lights and sound stay on across dirty track, frogs, and gaps. How do I connect the KA4?Solder the Blue wire to your decoder's keep-alive positive (V+) pad and the Black/White wire to the ground pad. It works with TCS decoders and most other brands that offer keep-alive connections — check your decoder's manual for the correct pads. How long will it keep my loco running?Expect roughly 6 to 20 seconds with headlights on for a typical HO locomotive, depending on motor efficiency and current draw.

Read more less

The Train Control Systems KA2 Keep-Alive® is a compact stay-alive capacitor pack that feeds backup power to your DCC decoder whenever the wheels lose contact with the rails. No more stalling on dirty track, dead frogs, or insulated turnouts. The KA2 comes in at about half the size of a KA4 and delivers roughly one-third the capacitance of a KA3/KA4, making it a great choice where space is tight in N and smaller HO locomotives. It includes Blue and Black-with-White-stripe lead wires to solder to your decoder's keep-alive pads (V+ and ground), so it works with TCS and most other-brand decoders that accept an external keep-alive. Browse more decoder add-ons in our DCC Accessories collection, shop the full Train Control Systems lineup, or pair it with a new sound decoder from our DCC Decoders collection. Features Keep-Alive® stay-alive capacitor pack eliminates stalling on dirty track, dead frogs, and insulated rail joints. Compact — about half the size of a KA4; delivers roughly one-third the capacitance of a KA3/KA4. Includes Blue and Black/White lead wires to solder to your decoder's keep-alive pads — works with TCS and most other-brand decoders. Dimensions: 0.35" x 0.35" x 0.61" (8.9 x 8.9 x 15.5 mm). Input rating 12–16V; works with any scale and any DCC system. More Information Brand Train Control Systems (TCS) Item Number 1456 (KA2) Type Keep-Alive / Stay-Alive Capacitor Pack Connection Blue + Black/White Wire Leads (solder-on) Dimensions 0.35" x 0.35" x 0.61" (8.9 x 8.9 x 15.5 mm) Input Rating 12–16V Scale Any Scale Condition New FAQ What does a Keep-Alive actually do?It stores an electrical charge and feeds it to your decoder when track power drops out, so the locomotive keeps moving and its lights and sound stay on across dirty track, frogs, and gaps. How do I connect the KA2?Solder the Blue wire to your decoder's keep-alive positive (V+) pad and the Black/White wire to the ground pad. It works with TCS decoders and most other brands that offer keep-alive connections — check your decoder's manual for the correct pads. Why choose the KA2 over a larger KA3/KA4?It's much smaller and fits where bigger packs won't — ideal for N scale and cramped HO shells. It holds less charge, so for longer run-through use a KA3 or KA4 if you have the room.

Read more less

The Digitrax LNRP3 LocoNet Repeater Module extends and protects your DCC layout's LocoNet network. With a fault-tolerant design, the LNRP3 automatically isolates problem segments so the rest of your layout keeps running — no manual intervention needed. A built-in color LCD with soft-key menus makes setup and diagnostics easy, even on complex installations. Features Isolates up to 3 segments of your LocoNet layout Primary P-port bi-directional LocoNet repeater to A/B/C expansion ports Fault-tolerant: A/B/C ports automatically disconnect and reconnect faulted segments, keeping all unfaulted ports active Color LCD with soft-key menus and selection knob for easy setup Extends large LocoNet installations of more than 20 devices Acts as a diagnostic tool when LocoNet network problems occur Boosts and separates Railsync outputs from the master command station Over-current protected Railsync with automatic retry on fault clearance Specifications Power Input 15V–18V DC, up to 250mA (side DC power jack) Ports 1 P-port (primary) + 3 expansion ports (A/B/C) Display Color LCD with soft-key menus and selection knob Compatibility All Digitrax LocoNet systems Item Number LNRP3 Brand Digitrax FAQ Do I need a separate power supply?Yes — each LNRP3 requires its own dedicated 15V–18V DC power supply (not included). Check Digitrax's accessories for compatible options. How many devices can the LNRP3 support?The LNRP3 is designed to extend LocoNet installations with more than 20 devices, splitting the network into up to 3 isolated segments. What happens when a segment has a fault?The LNRP3 automatically disconnects the faulted A/B/C port while keeping all other ports active. It then automatically attempts to reconnect once the fault is cleared. Is this compatible with my command station?The LNRP3 is compatible with all Digitrax LocoNet systems. Browse our full DCC Accessories collection for other compatible items. Related Collections Browse more DCC Accessories or explore our full Digitrax lineup at Squeaky's Trains & Things.

Read more less

The Train Control Systems KA4-P Keep-Alive® is a compact stay-alive capacitor pack that feeds backup power to your DCC decoder whenever the wheels lose contact with the rails. No more stalling on dirty track, dead frogs, or insulated turnouts — the KA4-P keeps a locomotive running with its lights and sound on for roughly 6 to 20 seconds during a power interruption, depending on the locomotive and motor efficiency. This is the harness-equipped version: it ships with a 2-Pin Quick Connector Harness that plugs straight into any decoder with a compatible 2-pin Keep-Alive socket, such as the TCS T4 and other current TCS decoders — no soldering to the decoder required. Electrically it works in any scale, and its tiny .52" footprint tucks easily into HO and larger locomotives. Browse more decoder add-ons in our DCC Accessories collection, shop the full Train Control Systems lineup, or pair it with a new sound decoder from our DCC Decoders collection. Features Keep-Alive® stay-alive capacitor pack eliminates stalling on dirty track, dead frogs, and insulated rail joints. Powers an HO locomotive with headlights on for approximately 6–20 seconds during a power interruption. Includes a 2-Pin Quick Connector Harness — plugs into the TCS T4 and other decoders with a compatible 2-pin socket, no decoder soldering needed. Ultra-compact: just .52" x .52" x .45" (13.22 x 13.22 x 11.55 mm) — fits HO and larger locomotives. Works with any scale and any DCC system; pairs with TCS and most other-brand decoders that accept an external keep-alive. More Information Brand Train Control Systems (TCS) Item Number 2005 (KA4-P) Type Keep-Alive / Stay-Alive Capacitor Pack Connection 2-Pin Quick Connector Harness Dimensions .52" x .52" x .45" (13.22 x 13.22 x 11.55 mm) Hold-Up Time ~6–20 sec (HO, lights on) Scale Any Scale (HO and larger recommended) Condition New UPC 879508007848 FAQ What does a Keep-Alive actually do?It stores an electrical charge and feeds it to your decoder when track power drops out, so the locomotive keeps moving and its lights and sound stay on across dirty track, frogs, and gaps. Will the KA4-P plug into my decoder?The included 2-pin harness plugs into TCS decoders with a compatible Keep-Alive socket (such as the T4) and most current TCS decoders. For decoders without a 2-pin socket, you can solder the leads to the decoder's keep-alive pads — check your decoder's manual first. What scales can use it?Electrically it works in any scale. Its small size suits HO and larger; in N scale it fits wherever there is room in the shell or tender. How long will it keep my loco running?Expect roughly 6 to 20 seconds with headlights on for a typical HO locomotive, depending on motor efficiency and current draw.

Read more less