DCC Decoders

By default, this decoder does not come with a pre-programmed Sound Profile. Nevertheless, we provide complimentary Sound File programming for all ESU decoders. Please be aware that opting for Sound File Programming in your order might result in a shipment delay of 1 to 2 business days. Visit this link to preview ESU Sounds 8-Pin NEM652 Harness Plug, 30 x 15.5mm Version The LokSound 5 is the most important member of the LokSound family. Due to the combination of the digital decoder and the sound module on one circuit board we achieve the smallest possible dimensions of 30 mm x 15.5 mm. Therefore it fits into almost any H0 or 0 gauge locomotive. LokSound 5 decoders are available with all popular interface types and are supplied with a sugar cube speaker (11 mm x 15 mm) and a sound enclosure. The LokSound 5 DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Please note the LokSound 5 DCC decoder does not come with a speaker. Operating modes Like all products of the LokSound family the LokSound 5 is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations. This decoder supports all DCC programming modes and thanks to RailCom® you may read out the CV values on the main, provided you have a command station supporting RailCom®. There are utility registers for command stations that only facilitate programming of CVs ranging from 1 to 255. Motorola® users benefit from up to 28 speed steps for 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. An integral programming mode even allows programming with the good old Central Unit 6021. The M4 protocol supports the automatic registration on mfx® compatible central units. The LokSound 5 decoder supports the Märklin® braking sections just as well as the ZIMO® HLU braking commands or the Lenz® ABC system. Braking with DCC brake generators or with DC is also possible. Furthermore the locomotive with a LokSound will come to a halt when a Selectrix® braking diode is switched into the circuit. The ABC push-pull feature enables the automatic commuting between two stations. The LokSound 5 decoder is also suitable for analogue DC and AC (!) layouts. Sound The LokSound 5 decoder can reproduce up to 10 channels simultaneously. Each channel offers up to 16 Bit / 31250 kHz and thus we have finally achieved hi-fi sound quality on your layout. For all practical purposes one cannot detect any difference to the original. A class D audio power amplifier with up to 3W output power feeds the speakers with a permitted impedance of 4 – 32 Ohms. The huge 128 MBit sound memory assures sufficient storage capacity. The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles. Functions We are quite aware that you want your locomotives to be as realistic as possible. Therefore we have packed many function outputs into it.  Subject to the type of interface every LokSound 5 has at least 10 amplified outputs. The decoders with PluX22 or 21MTC interface have an additional 4 outputs for controlling servos or as logic outputs. Of course, all important lighting functions are supported. The brightness of each output may be adjusted separately. The decoder supports the automatic push and pull movements – known as the coupler waltz - required for reliable operation of digital couplers such as the ones by ROCO® and Krois® as well as Telex® couplers. Motor control Motor control of the LokSound 5 has been further improved. A variable PWM pulse frequency ranging from 10 kHz to 50 kHz assures perfect silent operation, particularly for coreless motors. Thus the typical hum is a thing of the past. Load control can now be adjusted with up to 10 separate CVs and thus will manage even the most difficult cases. The unique “Auto Tune” function facilitates the automatic calibration of the decoder to perfectly match the motor. The LokSound 5 decoder supplies up to 1.5A motor current, which is quite sufficient even for older motor types. LokSound 5 DCC The LokSound 5 DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. More Information Item # 58420 Brand ESU Scale HO & O WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

By default, this decoder does not come with a pre-programmed Sound Profile. Nevertheless, we provide complimentary Sound File programming for all ESU decoders. Please be aware that opting for Sound File Programming in your order might result in a shipment delay of 1 to 2 business days. Visit this link to preview ESU Sounds The LokSound 5 micro DCC Direct Kato USA has been specially developed for installation in track N vehicles of the Kato USA brand: Most diesel locomotives of this manufacturer are installed in the American model of these decoders instead of the analog board installed as standard. Finally, these models can also be easily retrofitted with a LokSound decoder. The LokSound 5 micro DCC Direct Kato USA with its dimensions of 60.0mm x 10.1mm is a pure DCC decoder and comes without a loudspeaker. Modes The LokSound 5 micro DCC Direct Kato USA is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders log in fully to a suitable digital center.It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokSound 5 micro DCC Direct Kato USA Decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake blocks or dc voltage is also possible. In addition, it also stops with a Selectrix® brake diode. An AUTOMATIC ABC commuter train allows automatic commuting between two stations. The LokSound 5 micro DCC Direct Kato USA can be used on analog DC webs.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Sound The LokSound 5 micro DCC Direct Kato USA Decoder can play up to 12 channels simultaneously. Each channel can be resolved with up to 16 bits / 31250 kHz and offers hi-fi quality on its system. There is virtually no difference to the original audible anymore. A Class-D audio output with up to 3W output power controls the speakers, which can have between 4 ohms and 32 ohms impedance. A 128 Mbit sound memory provides enough capacity. All individual noises can be adjusted individually in the volume. The super-flexible sound engine without a rigid schedule allows the exemplary simulation of all conceivable rail tracks. Functions Despite its compact dimensions, the LokSound 5 micro DCC Direct Kato USA is equipped with an enormen number of function outputs. Two directly soldered SMD LEDs are designed for front and rear front and rear head lighting. For older models, two wired LEDs can alternatively be soldered and switched separately. Three further reinforced function outputs are also available. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokSound 5 micro DCC Direct Kato USA has a variable PWM clock frequency from 10kHz to 50kHz, which ensures super-quiet operation, especially for bell anchor motors – the typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. The LokSound 5 micro DCC Direct Kato USA decoder delivers up to 0.9A motor power. Operational reliability A PowerPack can be connected to the LokSound 5 micro DCC Direct Kato USA on request to bridge dirty rail sections. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. More Information Item # 58741 Brand ESU Scale N WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

By default, this decoder does not come with a pre-programmed Sound Profile. Nevertheless, we provide complimentary Sound File programming for all ESU decoders. Please be aware that opting for Sound File Programming in your order might result in a shipment delay of 1 to 2 business days. Visit this link to preview ESU Sounds With its unique design LokSound 5 DCC Direct, with integrated PowerPack can easily replace boards that provide poor motor control, low volume, or generally inferior sound. Not only will the decoder work fine with most factory installed speakers, but it will sound even better with our new 11x15mm “sugar cube” speaker and sound enclosure kits. Worried about dead spots or pesky yard ladder switches? There’s no need as we’ve built in ESU PowerPack direct into the decoder! Modes The LokSound 5 DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. With its size of 0.67x2.72 inch / 17x69 mm the LokSound 5 DCC Direct, with integrated PowerPack will fit in almost all of the popular North American and Australian H0 manufacturers locomotives. In the DCC format, 14 to 128 speed steps are as natural as 2- and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on fully automatically to a suitable digital central unit. It masters all DCC programming modes and, thanks to RailCom®, the CV values on the main track can be read out with suitable control panels. For panels that can only program the CVs from 1-255, there are auxiliary registers. Braking with DCC brake modules or DC voltage is also possible. An automatic ABC shuttle allows automatic commuting between two stations. The LokSound 5 DCC Direct, with integrated PowerPack decoder can also be used on analog DC tracks. Sound The LokSound 5 DCC Direct, with integrated PowerPack can play up to 10 channels simultaneously. Each channel can be resolved with up to 16 bit / 31250 kHz and finally offers hi-fi quality on your system. There is virtually no difference to the original more audible. A Class D audio power amplifier with up to 3W output powers the speakers, which may have between 4 ohms and 32 ohms impedance. The huge 128 Mbit sound storage provides enough capacity. All individual sounds can be individually adjusted in volume. The super flexible Sound engine without rigid schedule allows the prototypical simulation of all imaginable locomotives. Three separately adjustable braking functions and two alternative load scenarios give you the maximum control over your Locos. Features We know that you want your locomotives to be as realistic as possible. That’s why we packed the LokSound 5 DCC Direct, with integrated PowerPack with function outputs. Depending on the interface version, the LokSound 5 DCC Direct with integrated PowerPack decoder offers at 10 amplified function outputs. Of course tons of lighting effects are also available. The brightness of each output can be set separately. In order to keep compatible with the thousands of LokSound Selects and LokSound V4 decoders already on the market we made sure to add many of the most popular features of that Generation! This Includes the Full Throttle features, including the Famous Drive Hold! Motor Control The engine control of the LokSound 5 DCC Direct, with integrated PowerPack has again been fundamentally improved. A variably adjustable PWM clock frequency of 10kHz to 50kHz ensures especially in bell armature motors for a super quiet operation - The typical “humming” is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique “Auto tune” function allows the automatic decompression of the decoder to the motor. The LokSound 5 DCC Direct, with integrated PowerPack decoder delivers up to 0.75A motor current enough juice for older engines. Energy Storage The LokSound 5 DCC Direct, with integrated PowerPack reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders. With its energy storage (1 Farad capacity) the unit supplies power to all light and motor functions as well as to the sound module. Subject to the energy consumption of your model it may continue to move for up to three seconds. The on board PowerPack incorporates an integral charging circuit controlled by the decoder. Because of this there are no limitations or need to disconnect it during programming like some non-ESU "keep-alive" devices. In order to avoid an undue load on the booster in case there are several models in the same booster sector, the charging current is limited. More Information Item # 58921 Brand ESU Scale HO WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

21MTC NEM660 Interface Version The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all characteristics, however, the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility comes with a cheaper price. LokPilot 5 decoders are offered with all common interfaces.  Modes The LokPilot 5 DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus® the decoders register automatically with a suitable DCC system like the ESU CabControl. The decoder accepts all DCC programming modes and thanks to RailCom® the CV values ​​can be read on the main track with RailCom equipped DCC systems. For command stations that only program the CVs from 1-255 auxiliary CV registers exist. The LokPilot 5 DCC decoder recognizes the Märklin® braking sections as well as the ZIMO® HLU / ZACKCommands or the Lenz® ABC system. Also braking with DCC brake modules or with DC voltageis possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle trainenables automatic commuting between two train stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The top speedcan be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5DCC packed with function outputs. Depending on the interface version, each LokPilot offers 5 DCCDecoder at least 10 amplified function outputs with 250mA output current each. In the executionswith PluX22 or 21MTC interface there are 4 outputs to control servos orLogic level outputs added. All-important lighting functions are available. The brightness of each outputcan be set separately. The decoder masters automatic pushing and pullingwhen uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The engine control of the LokPilot 5 DCC has been fundamentally improved again. A variably adjustablePWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors.Operation - The typical “hum” is a thing of the past. The load control now has up to10 CVs  which can be adjusted for difficult cases. The unique "Autotune" function enablesthe automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to 1.5A of motor current. Enough juice even for older motors. Operational safety On request, a PowerPack can be fitted to the LokPilot 5 DCC to bridge dirty rail sections. Protection Of course, all function outputs and the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. More Information Item # 59629  Brand ESU Scale HO & O WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

While LokPilot 5 decoders can undoubtedly meet all imaginable requirements of even the most demanding experts, many model railway eras are looking for a robust, high-quality DCC decoder for your standard requirements, which should also be affordable. The LokPilot 5 Basic was developed with the aim of offering a modern decoder with a reasonable range of functions at a reasonable price. The LokPilot 5 Basic comes in two versions: In addition to a version with an 8-pin NEM interface, a version with 21MTC interface is also available. This makes the LokPilot 5 Basic particularly suitable for use in track H0 vehicles. Modes The LokPilot 5 Basic is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 20 functions can be triggered. Thanks to RailComPlus®, the decoders log in fully automatically to a suitable digital center. It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokPilot 5 Basic Decoder detects the Märklin® brake distances as well as the Lenz® ABC system. Braking with DCC brake blocks or dc voltage is also possible.The LokPilot 5 Basic Decoder can be used on analog DC webs. The maximum speed can be set separately.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions The LokPilot 5 Basic has 4 reinforced function outputs in each version. In the 21MTC interface, there are 8 logic-level outputs at the interface, two of which are also suitable for controlling servos. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokPilot 5 Basic delivers up to 0.9A continuous current. A variable PWM clock frequency from 10kHz to 50kHz ensures super-quiet operation, especially for bell anchor motors – The typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. Operational reliability On request, a PowerPack can be connected to the LokPilot 5 Basic to bridge dirty rail cuts. Protection Of course, all function outputs as well as the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. More Information Item # 59029 Brand ESU Scale HO WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

By default, this decoder does not come with a pre-programmed Sound Profile. Nevertheless, we provide complimentary Sound File programming for all ESU decoders. Please be aware that opting for Sound File Programming in your order might result in a shipment delay of 1 to 2 business days. Visit this link to preview ESU Sounds 1.5A, NEM652 8-Pin Plug, 11x15mm Speaker and Enclosure Version The LokSound 5 is the most important member of the LokSound family. Due to the combination of the digital decoder and the sound module on one circuit board we achieve the smallest possible dimensions of 30 mm x 15.5 mm. Therefore it fits into almost any H0 or 0 gauge locomotive. LokSound 5 decoders are available with all popular interface types and are supplied with a sugar cube speaker (11 mm x 15 mm) and a sound enclosure. The LokSound 5 DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Operating modes Like all products of the LokSound family the LokSound 5 is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations. This decoder supports all DCC programming modes and thanks to RailCom® you may read out the CV values on the main, provided you have a command station supporting RailCom®. There are utility registers for command stations that only facilitate programming of CVs ranging from 1 to 255. Motorola® users benefit from up to 28 speed steps for 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. An integral programming mode even allows programming with the good old Central Unit 6021. The M4 protocol supports the automatic registration on mfx® compatible central units. The LokSound 5 decoder supports the Märklin® braking sections just as well as the ZIMO® HLU braking commands or the Lenz® ABC system. Braking with DCC brake generators or with DC is also possible. Furthermore the locomotive with a LokSound will come to a halt when a Selectrix® braking diode is switched into the circuit. The ABC push-pull feature enables the automatic commuting between two stations. The LokSound 5 decoder is also suitable for analogue DC and AC (!) layouts. Sound The LokSound 5 decoder can reproduce up to 10 channels simultaneously. Each channel offers up to 16 Bit / 31250 kHz and thus we have finally achieved hi-fi sound quality on your layout. For all practical purposes one cannot detect any difference to the original. A class D audio power amplifier with up to 3W output power feeds the speakers with a permitted impedance of 4 – 32 Ohms. The huge 128 MBit sound memory assures sufficient storage capacity. The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles. Functions We are quite aware that you want your locomotives to be as realistic as possible. Therefore we have packed many function outputs into it.  Subject to the type of interface every LokSound 5 has at least 10 amplified outputs. The decoders with PluX22 or 21MTC interface have an additional 4 outputs for controlling servos or as logic outputs. Of course, all important lighting functions are supported. The brightness of each output may be adjusted separately. The decoder supports the automatic push and pull movements – known as the coupler waltz - required for reliable operation of digital couplers such as the ones by ROCO® and Krois® as well as Telex® couplers. Motor control Motor control of the LokSound 5 has been further improved. A variable PWM pulse frequency ranging from 10 kHz to 50 kHz assures perfect silent operation, particularly for coreless motors. Thus the typical hum is a thing of the past. Load control can now be adjusted with up to 10 separate CVs and thus will manage even the most difficult cases. The unique “Auto Tune” function facilitates the automatic calibration of the decoder to perfectly match the motor. The LokSound 5 decoder supplies up to 1.5A motor current, which is quite sufficient even for older motor types. LokSound 5 DCC The LokSound 5 DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. More Information Item # 58410 Brand ESU Scale HO & O WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

The TCS WOW101 is a universal WOWSound decoder for HO locomotives with a 9-pin JST plug, or any loco that can't accept a motherboard or WOWKit. It plugs straight into a 9-pin socket or hard-wires in, works with TCS T-Series harnesses, and includes an auxiliary harness for your speaker, CAM, and Keep-Alive connections. This is the Steam version, delivering TCS's authentic steam sound set with synchronized chuff and a full suite of whistle, bell, and running effects. An on-board Keep-Alive® keeps it running smoothly across dirty track and dead frogs — no add-on capacitor needed. Pick a matching speaker from our DCC Accessories collection, browse more DCC Decoders, or shop the full Train Control Systems WOWSound lineup. Features CD-quality WOWSound — 16-bit audio at a 44.1 kHz sample rate. Authentic TCS's authentic steam sound set with synchronized chuff and a full suite of whistle, bell, and running effects. Back-EMF load compensation for superior slow-speed control under load. Quiet Drive super-quiet motor control for buzz-free running. Variable Momentum for custom acceleration and deceleration curves. Audio Assist® menu programming — set up sound and CVs right on the track, no computer required. Plugs into a 9-pin JST socket or hard-wires in; compatible with TCS T-Series harnesses. On-board Keep-Alive® for stutter-free operation over dirty track. More Information Brand Train Control Systems (TCS) Item Number 1517 Decoder WOW101-KA Type WOWSound DCC Sound Decoder Sound Steam Connection 9-pin JST plug or hard-wire (T-Series harness compatible) On-board Keep-Alive Yes Scale HO Scale Condition New FAQ Will this decoder fit my locomotive?The WOW101 suits any HO loco with a 9-pin JST plug or one you can hard-wire. It is compatible with TCS T-Series plug-and-play harnesses for many popular models. Do I need a separate speaker?Yes — this is the decoder only. Add a WOWSpeaker (or any 8 Ω DCC speaker) sized for your locomotive to hear the sound. What is Audio Assist?It's TCS's on-the-fly programming menu that walks you through sound and CV setup using your throttle and the decoder's own spoken prompts — no programming track or computer needed.

Read more less

The SoundTraxx 884606 is a BLU-1100 Blunami digital sound decoder with the Steam-2 sound set. Blunami is a Tsunami2 with a Bluetooth radio added, so it runs three ways: as a normal DCC decoder on any NMRA-compliant system, on plain DC, or in wireless mode straight from your phone or tablet. Wireless mode needs no command station and no programming track — an old DC power pack and the free Blunami app are enough, and CVs can be read and changed over Bluetooth while the locomotive is running. The app is free for iOS and Android. This version is the most compact decoder in the Blunami line — small enough for N scale, suited to N, HO and small S scale. Features 90 selectable whistles — the Steam-2 library carries 27 more than the standard Steam set, most of them roadname-specific — plus 12 bells, 10 airpumps and 8 dynamos Bluetooth control from the free Blunami app (iOS and Android) — over 300 settings without editing a single CV by hand Dynamic Digital Exhaust (DDE) automatically matches exhaust volume and RPM to the load on the motor, and the app calibrates it for you Independent and train brakes with adjustable rates Hyperdrive2 motor control for smooth, creep-speed switching Over 20 Hyperlight lighting effects across 4 function outputs 16 polyphonic sound channels on a 32-bit processor, with a 7-band equalizer and adjustable reverb CurrentKeeper ready — works with the SoundTraxx 810140 CurrentKeeper More Information Item Number: SoundTraxx 884606 Model: BLU-1100 Blunami Sound Set: Steam-2 Steam Scale: N, HO and small S scale Decoder Size: 31 x 10.5 x 5mm Connection: Hardwire (single wires) Max. Motor Stall Current: 1A Function Outputs: 4 Audio Amplifier: 1 Watt, 8-Ohm Load DCC Track Voltage: 7V – 22V Sound Channels: 16 polyphonic Processor: 32-bit, 28 functions Control Modes: DC, DCC and Bluetooth wireless Shop the full SoundTraxx range, compare every DCC decoder we stock, or see the other Steam-2 sound profile decoders. A speaker is not included — browse DCC speakers rated 1 watt or better, and find install parts in DCC wiring. Add a SoundTraxx 810140 CurrentKeeper to keep sound alive over dirty track and turnouts. FAQ Do I need a DCC system to use this?No. That is the point of Blunami. It runs on a plain DC power pack with no command station at all — you control it from the free Blunami app over Bluetooth. It is also a fully NMRA-compliant DCC decoder if you already run DCC. Does the app work on Android?Yes. The free Blunami app is published for both iOS and Android. (Some older listings and dealer pages still say iOS only — that is out of date.) Is a speaker included?No. Pair it with an 8-ohm speaker rated 1 watt or better that fits your shell. How is Steam-2 different from the standard Steam set?The chuffs, bells, airpumps and dynamos are the same. The difference is the whistle library: Steam-2 offers 90 whistles versus 63 on the standard set, with many roadname-specific additions. Will it fit my locomotive?This one measures 31 x 10.5 x 5mm and connects by hardwire (single wires). Check the space in your shell against that footprint before ordering — other Blunami versions use different connectors and sizes.

Read more less

The SoundTraxx 885623 is a BLU-21PNEM8 Blunami digital sound decoder with the EMD-2 sound set. Blunami is a Tsunami2 with a Bluetooth radio added, so it runs three ways: as a normal DCC decoder on any NMRA-compliant system, on plain DC, or in wireless mode straight from your phone or tablet. Wireless mode needs no command station and no programming track — an old DC power pack and the free Blunami app are enough, and CVs can be read and changed over Bluetooth while the locomotive is running. The app is free for iOS and Android. This version is the 21-pin MTC plug-in Blunami, suited to HO scale and larger. Features 8 EMD-2 prime movers: EMD 567 12-cylinder (no transition), EMD 567C 16-cylinder non-turbo, EMD 645E 12-cylinder non-turbo, EMD 645E 12-cylinder turbo, EMD 645F 16-cylinder turbo, EMD 645E 20-cylinder turbo, EMD 710G 12-cylinder, EMD 710G 16-cylinder Over 40 air horns and 13 bells, plus air compressors, couplers and dynamos Bluetooth control from the free Blunami app (iOS and Android) — over 300 settings without editing a single CV by hand Dynamic Digital Exhaust (DDE) automatically matches exhaust volume and RPM to the load on the motor, and the app calibrates it for you Three braking types: independent, train and dynamic braking Hyperdrive2 motor control for smooth, creep-speed switching Over 20 Hyperlight lighting effects across 8 function outputs 16 polyphonic sound channels on a 32-bit processor, with a 7-band equalizer and adjustable reverb CurrentKeeper ready — works with the SoundTraxx 810140 CurrentKeeper More Information Item Number: SoundTraxx 885623 Model: BLU-21PNEM8 Blunami Sound Set: EMD-2 Diesel Scale: HO scale and larger Decoder Size: 30.5 x 15.5 x 6.5mm Connection: NEM660 21MTC integral connector Max. Motor Stall Current: 1A Function Outputs: 8 Audio Amplifier: 2 Watt, 8-Ohm Load Sound Channels: 16 polyphonic Processor: 32-bit, 28 functions Control Modes: DC, DCC and Bluetooth wireless Shop the full SoundTraxx range, compare every DCC decoder we stock, or see the other EMD-2 sound profile decoders. A speaker is not included — browse DCC speakers rated 2 watt or better, and find install parts in DCC wiring. Add a SoundTraxx 810140 CurrentKeeper to keep sound alive over dirty track and turnouts. FAQ Do I need a DCC system to use this?No. That is the point of Blunami. It runs on a plain DC power pack with no command station at all — you control it from the free Blunami app over Bluetooth. It is also a fully NMRA-compliant DCC decoder if you already run DCC. Does the app work on Android?Yes. The free Blunami app is published for both iOS and Android. (Some older listings and dealer pages still say iOS only — that is out of date.) Is a speaker included?No. Pair it with an 8-ohm speaker rated 2 watt or better that fits your shell. Which prime movers do I get?All 8 listed above, selectable in the app or via CV 123. You are not locked to one engine sound — pick whichever matches your prototype. EMD-2 or plain EMD — which do I want?This is the EMD-2 set: a second collection of less-common EMD prime movers, called out by cylinder count. The plain EMD set covers the more common 567/645/710 variants. Match the list above to your prototype. Will it fit my locomotive?This one measures 30.5 x 15.5 x 6.5mm and connects by nem660 21mtc integral connector. Check the space in your shell against that footprint before ordering — other Blunami versions use different connectors and sizes.

Read more less

The TCS 1516 WOW101 Steam is a universal WOWSound decoder for HO locomotives with a DCC-ready 9-pin JST plug, or any locomotive that can't take a motherboard or WOWKit. It plugs straight into a 9-pin socket or hard-wires in, works with any TCS T-Series harness, and includes an auxiliary harness for your speaker, CAM, Keep Alive and the extra F3 and F4 lighting functions. The steam sound set uses TCS's Chuffinity chuff library and True Scale Sound, which changes chuff intensity with the load, and the CAM input lets you synchronize the chuff to your drivers. Pair it with a WOWSpeaker sized for your locomotive. Specifications Brand Train Control Systems (TCS) Item Number 1516 UPC 879508004700 Decoder WOW101-Steam Type WOWSound DCC sound decoder Sound Steam Audio 16-bit, 44.1 kHz sample rate Connection 9-pin JST plug or hard-wire, T-Series harness compatible Keep Alive Not built in; connection on the auxiliary harness Lighting 20 programmable effects, F3 and F4 on the auxiliary harness LED Resistors Not on board; use external resistors with LEDs Speaker Not included Scale HO Condition New Features HD-quality WOWSound: 16-bit audio at a 44.1 kHz sample rate Steam sound set with Chuffinity, a large chuff library that never falls into a repeating pattern True Scale Sound changes chuff intensity with the load CAM input to synchronize the chuff to driver rotation Rotate through every whistle and bell on the decoder with one button Plugs into a 9-pin JST socket or hard-wires in; compatible with any TCS T-Series harness Back-EMF load compensation for smooth slow-speed control Quiet Drive motor control for buzz-free running Automatic DC mode detection Variable momentum and user-loadable speed tables 20 user-programmable lighting effects with dimmable brightness Function remapping on F0 through F12; supports 12 volt bulbs Decoder Lock and Airwire compatibility Audio Assist menu programming: set up sound and CVs on the track, no computer required Frequently Asked Questions Do I need a separate speaker?Yes. A speaker is not included. Choose one sized for your locomotive from our DCC Speakers. Can I use LED lighting?Yes, with external resistors. WOW101 decoders do not have on-board resistors. Can I add a Keep Alive?Yes. The auxiliary harness has a Keep Alive connection, and the TCS 1517 WOW101-KA Steam is the same decoder with Keep Alive built in. Will this decoder fit my locomotive?It suits HO locomotives with a 9-pin JST plug, or ones you can hard-wire, and it works with TCS T-Series plug-and-play harnesses. What is Audio Assist?TCS's spoken programming menu. Your throttle and the decoder's own voice prompts walk you through sound and CV setup, so you don't need a programming track or a computer. Is there a diesel version?Yes, the TCS 1530 WOW101 Diesel. Explore More Browse more DCC Decoders, shop the full Train Control Systems lineup, or find a matching DCC Speaker.

Read more less

By default, this decoder does not come with a pre-programmed Sound Profile. Nevertheless, we provide complimentary Sound File programming for all ESU decoders. Please be aware that opting for Sound File Programming in your order might result in a shipment delay of 1 to 2 business days. Visit this link to preview ESU Sounds 4A for G Scale, Screw Terminals Version The LokSound 5 XL decoder is quite a big piece of equipment. It has to be, because it is intended for use in large scale model railways, e.g. garden railways and 1 gauge models. Its integral PowerPack matching the increased motor power assures reliable operation even on dirty tracks. The LokSound 5 XL measures 51 mm x 40 mm and is available in two different types: Besides the type with robust screw type terminals for installation in older models without an interface socket, there is a version with multi-pin connectors. This version fits into all locomotives where an older type LokSound XL decoder has been installed previously. Operating modes Like all products of the LokSound family the LokSound 5 XL is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations. The LGB® chain control is capable of handling functions and their respective buttons with older LGB® control systems. This decoder supports all DCC programming modes and thanks to RailCom® you may read out the CV values on the main, provided you have a command station supporting RailCom®. There are utility registers for command stations that only facilitate programming of CVs ranging from 1 to 255. Motorola® users benefit from up to 28 speed steps and 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. An integral programming mode even allows programming with the good old Central Unit 6021. The M4 protocol supports the automatic registration on mfx® compatible central units. The LokSound 5 XL decoder supports Märklin® braking sections just as well as the ZIMO® HLU braking commands or the Lenz® ABC system. Braking with DCC brake generators or with DC is also possible. Furthermore the locomotive with a LokSound 5 XL will come to a halt when a Selectrix® braking diode is connected to the circuit. The ABC push-pull feature enables the automatic commuting between two stations. The LokSound 5 XL decoder is also suitable for analogue DC and AC train sets. Sound The LokSound 5 XL decoder can reproduce up to 10 channels simultaneously. Each channel offers up to 16 Bit / 31250 kHz and thus we have finally achieved hi-fi sound quality on your layout. For all practical purposes one cannot detect any difference to the original. A dual class D audio power amplifier with up to 2 x 6W output power feeds the speakers with a permitted impedance of 4 – 32 Ohms. The sound volume can be controlled by means of two separate potentiometers. The huge 128 MBit sound memory assures sufficient storage capacity. The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles. Functions Every LokSound 5 XL decoder has 12 amplified function outputs. On top of that there are another 7 logic outputs, which can, if so desired, control four RC servos or SUSI extension modules. Of course, all important lighting functions are supported. The brightness of each output may be adjusted separately. The decoder supports the automatic push and pull movements – known as the coupler waltz - required for reliable operation of digital couplers such as the ones by ROCO® and Krois® as well as Telex® couplers. 3 sensor inputs may be employed in order to trigger functions. Motor control Motor control of the LokSound 5 XL has been further improved. A variable PWM pulse frequency ranging from 10 kHz to 50 kHz assures perfect silent operation, particularly for coreless motors. Thus the typical hum is a thing of the past. Load control can now be adjusted with up to 10 separate CVs and thus will manage even the most difficult cases. The unique “Auto Tune” function facilitates the automatic calibration of the decoder to perfectly match the motor. The LokSound 5 XL decoder supplies ample current for the motor, namely up to 5.0 A (4.0 A continuous).  Thus the decoder can also handle G gauge locomotives by PIKO® as well as locomotives with two Bühler® or Mabuchi® motors. More Information Item # 58513 Brand ESU Scale G WARNING: This product can expose you to a chemical, which is known to the State of California to cause Cancer and Reproductive Harm - For more information go to www.P65Warnings.ca.gov

Read more less

The SoundTraxx 884808 is a TSU-21PNEM8 Tsunami2 digital sound decoder with the Steam-2 sound set. Tsunami2 combines a 16-bit sound system, Hyperdrive2 motor control, Hyperlight lighting effects and a full NMRA-compliant DCC decoder on one board, driven by a 32-bit processor with 16 polyphonic sound channels. This version is the 21-pin MTC plug-in decoder, rated 1A and suited to HO scale and larger. Dynamic Digital Exhaust reads the load on the motor and notches the engine up and down on its own, so the locomotive sounds like it is working for its train. Features 90 selectable whistles — 27 more than the standard Steam set — plus 10 exhaust chuffs, 12 bells, 10 airpumps and 8 dynamos Dynamic Digital Exhaust (DDE) matches exhaust volume and RPM to the load on the motor automatically Independent and train brakes with adjustable rates Hyperdrive2 motor control for smooth, creep-speed switching Over 20 Hyperlight lighting effects across 8 function outputs 16 polyphonic sound channels on a 32-bit processor, with a 7-band equalizer and adjustable reverb CurrentKeeper ready — works with the SoundTraxx 810140 CurrentKeeper More Information Item Number: SoundTraxx 884808 Model: TSU-21PNEM8 Tsunami2 Sound Set: Steam-2 Steam Scale: HO scale and larger Decoder Size: 30.5 x 15.5 x 6.5mm Connection: 21-pin NEM (21MTC) plug Max. Motor Stall Current: 1A Function Outputs: 8 Audio Amplifier: 2 Watt, 8-Ohm Load DCC Track Voltage: 7V – 22V Sound Channels: 16 polyphonic Processor: 32-bit, 28 functions Shop the full SoundTraxx range, compare every DCC decoder we stock, or see the other Steam-2 sound profile decoders. A speaker is not included — browse DCC speakers rated 2 watt or better, and find install parts in DCC wiring. Add a SoundTraxx 810140 CurrentKeeper to keep sound alive over dirty track and turnouts. FAQ Will this fit my locomotive?It measures 30.5 x 15.5 x 6.5mm and connects by 21-pin nem (21mtc) plug. Check that against the space in your shell before ordering — other Tsunami2 versions use different connectors and sizes. Is a speaker included?No. Pair it with an 8-ohm speaker rated 2 watt or better that fits your shell. How is Steam-2 different from the standard Steam set?The chuffs, bells, airpumps and dynamos are the same. The difference is the whistle library: Steam-2 offers 90 whistles against 63 on the standard Steam set, with many roadname-specific additions. Does it run on DC?Yes. Tsunami2 runs on a standard DC power pack as well as DCC, though sound and lighting options are limited on DC. Full function control needs a DCC system.

Read more less