Black Friday - 15% Off

The Digitrax SE74 is the signal and turnout decoder that ties a working signal system to your LocoNet. It drives signal masts, throws four turnouts, reads eight input lines for sensors and local push buttons, and stores eight routes of eight entries each - which means interlockings and crossovers can be set from a single command instead of one turnout at a time. Signalling your layout? Browse our DCC Accessories, DCC Wiring, and the full Digitrax range. Features Fully connectorized installation - signal driver cables and turnout leads plug in, so a signal bay can be built on the bench and dropped under the layout. Four turnout outputs, configurable for solenoid machines (Peco, Atlas, Kato) or slow-motion machines such as the Tortoise. 8 input lines for block detectors, sensors and local control buttons at the fascia. 8 system routes with 8 entries each - throw a whole crossover or interlocking from one command. Optional DCC 9-aspect control mode, including Lunar aspects, for prototypical signalling. Setup via option switches or LocoNet programming, with Series 7 style configuration from a DT602 throttle. More Information Brand Digitrax Item Number SE74 Product Type DCC Signal and Turnout Decoder Scale All scales Turnout Outputs 4 - solenoid or slow-motion Input Lines 8 Routes 8 routes x 8 entries Signal Aspects Up to 9-aspect DCC mode including Lunar Connection LocoNet, connectorized signal driver cables Condition New FAQ What else do I need to get signals running?The SE74 plus signal masts and a way to carry the connections to them. Most installs use a Signal Driver Cable Kit (SDCK) for the ribbon cable and sockets, plus mast bases and mounting hardware. You also need occupancy detection - the SE74 displays aspects, it does not detect trains on its own. Can it drive slow-motion turnout machines?Yes. The four turnout outputs are configurable for either solenoid machines such as Peco, Atlas and Kato, or stall-motor machines such as the Tortoise. What are routes and why do they matter?A route sets several turnouts at once from a single command. With eight routes of eight entries you can line an entire crossover or interlocking with one button press instead of throwing each point individually. Do I need a Digitrax command station?Yes for full configuration - the SE74 is a LocoNet device and is set up over LocoNet, with the most convenient programming from a DT602 throttle.

Read more less

The Digitrax SNABC is a complete turnout signalling kit in N scale. A turnout takes three signals to do properly - a dual-head mast facing the points that shows both routes, plus single-head masts covering each leg beyond - and the kit includes all three along with the mounting board, plugs and hardware. Current-limiting resistors are already fitted, which matters more in N scale where the LEDs are small and unforgiving. Signalling your layout? Browse our DCC Accessories, DCC Wiring, and the full Digitrax range. What's Included Item Qty Dual Head A Signal 1 Single Head B Signal 1 Single Head C Signal 1 SMP1 signal mast plug 3 Spacers 6 Screws 6 Features Everything for one N scale turnout signal plant - three signals, mast plugs, spacers and screws. Dual-head A signal for the straight and diverging routes at the points, plus B and C single heads for each leg. Plug and play 10-pin connectors so signals lift out during ballasting and scenery work - worth a lot on an N scale layout where everything is close together. Current-setting resistors built into the board - nothing to calculate, nothing to solder. Pads are provided to attach any signal head to the mast base if you want to mix in other manufacturers. Intended for use with the Digitrax SE8C signal decoder. More Information Brand Digitrax Item Number SNABC Product Type Signal Kit Scale N Configuration Turnout - A, B and C masts Signal Heads 1 dual head, 2 single head Connector 10-pin plug and play Resistors Built into the mounting board Use With Digitrax SE8C signal decoder Condition New FAQ What is the difference between this and a mainline kit?A turnout needs three signals: a dual-head mast protecting the points and showing both routes, plus single-head masts for each leg beyond. A mainline kit only covers plain double track. Is this the N scale version of the SHABC?Yes. Same configuration and the same contents, with signal heads scaled for N. Do I need anything else to make the signals work?Yes - a signal decoder to drive the aspects (the SE8C is the intended partner), cabling to reach the masts such as the SDCK kit, and some form of block occupancy detection. Do I need to add resistors?No. Current-setting resistors are already on the mounting board, so there is no resistor maths and no risk of over-driving an LED.

Read more less

The Digitrax SHABC is a complete turnout signalling kit for HO scale. A turnout needs three signals to be done properly - a dual-head mast facing the points that can show both routes, and single-head masts covering each leg beyond - and that is exactly what is in the box, along with the mounting board, plugs and hardware. Current-limiting resistors are already fitted. Signalling your layout? Browse our DCC Accessories, DCC Wiring, and the full Digitrax range. What's Included Item Qty Dual Head A Signal 1 Single Head B Signal 1 Single Head C Signal 1 SMP1 signal mast plug 3 Spacers 6 Screws 6 Features Everything for one turnout signal plant - three signals, mast plugs, spacers and screws in one box. Dual-head A signal to show both the straight and diverging routes at the points, plus B and C single heads for each leg. Plug and play 10-pin connectors so signals lift out when you are ballasting or working on scenery. Current-setting resistors built into the board - nothing to calculate, nothing to solder. Pads are provided to attach any signal head to the mast base if you want to mix in other manufacturers. Intended for use with the Digitrax SE8C signal decoder. More Information Brand Digitrax Item Number SHABC Product Type Signal Kit Scale HO Configuration Turnout - A, B and C masts Signal Heads 1 dual head, 2 single head Connector 10-pin plug and play Resistors Built into the mounting board Use With Digitrax SE8C signal decoder Condition New FAQ What is the difference between this and a mainline kit?A turnout needs three signals, not two: a dual-head A mast protecting the points and showing both routes, plus single-head B and C masts for each leg beyond. A mainline kit such as the SH2AB only covers plain double track. Do I need anything else to make the signals work?Yes - a signal decoder to drive the aspects (the SE8C is the intended partner), cabling to reach the masts such as the SDCK kit, and some form of block occupancy detection. Do I need to add resistors?No. Current-setting resistors are already on the mounting board, so there is no resistor maths and no risk of over-driving an LED. Can I mix in signal heads from other makers?Pads are provided on the mast base so you can attach other signal heads if you want a specific prototype. The plug arrangement and resistor board are designed around the Digitrax SE8C.

Read more less

The Digitrax SMBK is a three-pack of signal mast bases - the part that sits in the scenery, takes the plug from the signal driver cable and holds the signal head at the right height. Use them as bases under signals in any scale, or paint and detail them and they work as finished N scale signal masts in their own right. Signalling your layout? Browse our DCC Accessories, DCC Wiring, and the full Digitrax range. Features Three signal masts per pack, enough for a full turnout signal plant or three mainline positions. Works as a mast base in any scale - it carries the plug connection and sets the signal at the right height above the scenery. Doubles as a finished N scale mast once painted and detailed, so one part covers two jobs. Designed to mate with the 10-pin signal plugs used across the Digitrax signalling range. Pairs with the SMHK mounting hardware kit, which holds the plugs at the right distance under the layout. More Information Brand Digitrax Item Number SMBK Product Type Signal Mast Base Kit Scale All scales as a base, N scale as a finished mast Quantity 3 signal masts Connector For 10-pin Digitrax signal plugs Finish Unpainted - paint and detail as required Condition New FAQ What does a mast base actually do?It anchors the signal through the layout surface and carries the plug connection down to the signal driver cable underneath, so the signal itself stays removable. Can I use these in HO or O scale?Yes, as bases. At those scales the base sits below or behind the scenery and the visible mast is your signal head assembly. Only in N scale is the part itself convincing as the finished mast. What else do I need?A signal head or kit, cabling such as the SDCK, and the SMHK mounting hardware kit to hold the plugs at the correct depth under the benchwork. Do they come painted?No. They are supplied plain so you can paint and weather them to match your prototype.

Read more less

The Digitrax SH2AB is a complete mainline signalling kit for HO scale - four single-head signals in the A and B mast configurations used to signal a double-track main, with the mounting board, plugs and hardware to install them. The current-limiting resistors are already on the board, so there is nothing to calculate and nothing to solder on the bench. Signalling your layout? Browse our DCC Accessories, DCC Wiring, and the full Digitrax range. What's Included Item Qty Single Head A Signal 2 Single Head B Signal 2 SMP1 signal mast plug 4 Spacers 8 Screws 8 Features Everything for one mainline signal plant - signals, mast plugs, spacers and screws in one box. Plug and play 10-pin connectors make each signal removable, which matters when you are ballasting or working on scenery nearby. Current-setting resistors built into the board - no resistor maths, no risk of cooking an LED. A and B mast configurations for straightforward double-track mainline signalling. Pads are provided so you can attach any signal head to the mast base if you want to mix in other manufacturers. Intended for use with the Digitrax SE8C signal decoder. More Information Brand Digitrax Item Number SH2AB Product Type Signal Kit Scale HO Configuration Mainline - A and B masts Signal Heads 4 single head Connector 10-pin plug and play Resistors Built into the mounting board Use With Digitrax SE8C signal decoder Condition New FAQ What does a mainline kit signal, compared with a turnout kit?This one covers plain double track - two directions, A and B masts. For a junction or crossover you want a turnout kit such as the SHABC, which includes a dual-head signal for the diverging route. Do I need anything else to make the signals work?Yes - a signal decoder to drive the aspects (the SE8C is the intended partner), cabling to reach the masts such as the SDCK kit, and some form of block occupancy detection. Do I need to add resistors?No. Current-setting resistors are already on the mounting board, which is one of the main reasons to buy the kit rather than loose signal heads. Will these work with a non-Digitrax system?The signal heads themselves are just LEDs on a board and can be driven by other signal systems, but the 10-pin plug arrangement and the resistor board are designed around the Digitrax SE8C.

Read more less

The Digitrax SMHK is the under-layout hardware that makes a signal install workable. Six metal straps and six spacers hold each signal plug at exactly the right distance below the benchwork, so when you push a signal down through the scenery it meets its socket squarely instead of you working blind with one arm under the layout. Signalling your layout? Browse our DCC Accessories, DCC Wiring, and the full Digitrax range. What's Included Item Qty Metal signal straps 6 Signal spacers 6 Features Holds signal plugs at the correct depth under the layout so signals plug in first time, every time. Six straps and six spacers - enough hardware for six signal positions. Metal straps hold their set position rather than drifting once the layout warms up or gets knocked. Designed around the 10-pin signal plugs used across the Digitrax signalling range. Pairs with the SMBK mast base kit and the SDCK signal driver cable kit to complete an install. More Information Brand Digitrax Item Number SMHK Product Type Signal Mounting Hardware Kit Scale All scales Contents 6 metal straps, 6 spacers Mounting Under-layout Use With Digitrax signal driver cables and mast bases Condition New FAQ Why do I need mounting hardware at all?Because plugging a signal in from above with your hand underneath the layout is miserable without it. The straps hold each plug rigid at a known depth so the signal seats cleanly when you push it down. How many signals does one kit cover?Six positions - six straps and six spacers. What else do I need for a signal install?Signal heads or a signal kit, mast bases such as the SMBK, cabling such as the SDCK, and a signal decoder to drive the aspects. Will it work with signals from other manufacturers?The hardware holds the plug, not the signal, so it works wherever you are using Digitrax-style 10-pin signal plugs regardless of whose head is on top.

Read more less

N scale Mainline Signaling Kit including: 2 Single Head A Signals, 2 Single Head B Signals, 4 SMP1s, 8 spacers, 8 screws. Makes all of your signals plug ‘n play with small 10 pin connectors. Can be used as a basic N scale signal. Mounting board and hardware included. Current setting resistors are built in to the board. Easy mainline setup with A and B mast configurations. Pads are provided to make it easy to attach any signal to the mast base. This product is intended for use with the SE8C. The Digitrax Plug ‘N Play Signal Mast consists of a signal mast with one or two signal heads depending on mast configuration. Included with the kit are mounting boards and hardware that makes it easy to mount and connect the signal mast to the SE8C signal driver cable. This product is intended for use with the SE8C and other Digitrax signaling decoders. More Information Item # SN2AB Brand Digitrax MSRP $27.00 TCA Grading C-10 Mint - Brand New Availability In-Stock/Restockable Manuals Instruction Sheet

Read more less